1. Manuales
  2. Marcas
  3. e-conolight Manuales
  4. Equipo de Iluminación
  5. C-LITE C-WM-A-WLMO Serie
  6. Instrucciones de instalación

e-conolight C-LITE C-WM-A-WLMO Serie Instrucciones De Instalación

Ocultar thumbs
1
2
3
4
5
6
Idiomas disponibles

Idiomas disponibles

Tabla de contenido

INSTALLATION INSTRUCTIONS
C-WM-A-WLMO Series
CAUTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety
precautions should always be followed including the
following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1.
DANGER- Risk of shock- Disconnect power before
installation.
DANGER – Risque de choc – Couper l'alimentation
avant l'installation.
2.
This luminaire must be installed in accordance with the
NEC or your local electrical code. If you are not familiar
with these codes and requirements, consult a qualified
electrician.
Ce produit doit être installé conformément à NEC ou votre
code électrique local. Si vous n'êtes pas familier avec ces
codes et ces exigences, veuillez contacter un électricien
qualifié.
3.
Suitable for Wet Locations.
Adspte pour les Endroits Mouiles.
4.
WALL MOUNT ONLY.
INSTALLATION MURALE SEULEMENT.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
http://lighting.cree.com/warranty
Document:
LPN00669X0001A0_A
Created By:
TMT
MOUNTING
1.
Remove the lens by removing the 3 screws securing it to the
fixture back plate. Set screws aside for reinstalling later.
2.
Remove the 2 hex nuts above the LED board to separate the
fixture back plate from the rear mounting bracket. See Figure 1 on
the back page. Set nuts aside for reinstalling later.
NOTE: Do NOT touch the LED board during the installation
process.
3.
Attach fixture mounting bracket to junction box using hardware
supplied by others. Rotate crossbar of bracket so threaded studs
located on crossbar are horizontally positioned relative to each
other. Tighten two center screws on mounting bracket to fix
position of bracket. See Figure 1 on the back page.
4.
Make wiring connections per the Electrical Connections section.
5.
Slide fixture back plate over 2 threaded studs on mounting
bracket. For wet locations, a high grade caulking material, such
as silicone rubber, should be used between back gasket on fixture
back plate and mounting surface. See Figure 1 on the back
page.
6.
Secure back plate to mounting surface by tightening nuts removed
in Step 2 above.
7.
Replace lens by tightening the lens screw that were removed in
Step 1. Do Not overtighten screws to prevent damage to lens.
ELECTRICAL CONNECTIONS
Fixture is equipped with universal volt driver 120-277V
(ie. 120V, 208V, 240V or 277V)
PHASE TO NEUTRAL WIRING 120/277V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no
wires are pinched.
PHASE TO PHASE WIRING 208/240V
1. Connect supply ground to fixture ground (green) lead.
2. Connect supply L1 (Hot) to fixture neutral (white) lead.
3. Connect supply L2 (Hot) to fixture hot (black) lead.
Tuck all wires carefully into wiring chamber ensuring that no
wires are pinched.
|
1-800-236-6800
Date
1-27-2020
Tabla de contenido
loading

Manuales relacionados para e-conolight C-LITE C-WM-A-WLMO Serie

Resumen de contenidos para e-conolight C-LITE C-WM-A-WLMO Serie

  • Página 1 Document: LPN00669X0001A0_A Date 1-27-2020 INSTALLATION INSTRUCTIONS Created By: C-WM-A-WLMO Series MOUNTING Remove the lens by removing the 3 screws securing it to the fixture back plate. Set screws aside for reinstalling later. Remove the 2 hex nuts above the LED board to separate the fixture back plate from the rear mounting bracket.

  • Página 2: Installation Instructions

    Document: LPN00669X0001A0_A Date 1-27-2020 INSTALLATION INSTRUCTIONS Created By: C-WM-A-WLMO Series FIGURE 1 FCC NOTICE CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Página 3: Medidas De Seguridad Importantes

    Documento: LPN00669X0001A0_A Fecha 1-27-2020 INSTRUCCIONES DE INSTALACIÓN Creado por: Serie C-WM-A-WLMO MONTAJE Retire el lente, y para ello quite los 3 tornillos que lo fi jan a la placa posterior de la unidad. Deje los tornillos a un lado para volver a instalarlos más tarde.
  • Página 4 Documento: LPN00669X0001A0_A Fecha 1-27-2020 INSTRUCCIONES DE INSTALACIÓN Creado por: Serie C-WM-A-WLMO FIGURA 1 AVISO DE LA FCC PRECAUCIÓN: Los cambios o las modificaciones no aprobados podrían anular su autorización para usar este equipo. Este dispositivo cumple con la Sección 15 de las normas de la FCC. El funcionamiento está supeditado a las dos condiciones siguientes: (1) Este dispositivo no debe causar interferencias dañinas y (2) este dispositivo debe aceptar cualquier interferencia recibida, incluidas aquellas que puedan causar un uso indeseado.

  • Página 5: Mesures De Sécurité Importantes

    Document : LPN00669X0001A0_A Date 1-27-2020 INSTRUCTIONS D’INSTALLATION Créé par : Série C-WM-A-WLMO MONTAGE Retirez la lentille en retirant les 3 vis qui la fi xent à la plaque arrière du luminaire. Mettez les vis de côté afi n de les réinstaller ultérieurement.
  • Página 6 Document : LPN00669X0001A0_A Date 1-27-2020 INSTRUCTIONS D’INSTALLATION Créé par : Série C-WM-A-WLMO FIGURE 1 AVIS DE LA FCC MISE EN GARDE : Des modifications ou changements non expressément approuvés pourraient annuler votre autorisation d’utiliser cet équipement. Cet appareil est conforme à la section 15 du règlement FCC. L’utilisation est soumise aux deux conditions suivantes : (1) Cet appareil ne peut pas causer d’interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant causer un fonctionnement non désiré.

Tabla de contenido