Honeywell 44123 Guia De Inicio Rapido

44123 (12IN.), 44124 (18IN.), 44125 (24IN.),
44126 (36IN.)
PLUG-IN LED LIGHT FIXTURE
SAVE THESE INSTRUCTIONS FOR POSSIBLE FUTURE USE.
CAUTION: DO NOT OVER TIGHTEN SCREWS.
DO NOT USE WITH A DIMMING CIRCUIT OR ANY OTHER
ELECTRONICALLY SWITCHED CONTROL.
IMPORTANT SAFETY INSTRUCTIONS
The LED light fixture has a polarized plug (one blade is wider than the other) to reduce the risk
of electric shock. This plug fits in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an
extension cord unless plug can be fully inserted. Do not alter the plug. Read entire installation
instructions before you begin.
INSTALLATION PROCEDURE FOR PLUG-IN LIGHT FIXTURE
Carefully plan your installation prior to mounting the LED light
fixture. For kitchen installations, the recommended mounting for
the LED light fixture is near the front lip of your kitchen cabinets
with the light source facing forward as shown in Figure 1. This
provides the best light distribution across a countertop. Make
sure the 5ft. line cord will reach the nearest electrical outlet and
the LED light fixture.
1. DO NOT ATTEMPT TO INSTALL LED LIGHT FIXTURE
WHILE PLUGGED IN.
2. Select a suitable dry mounting location (for use indoors
only). Make sure mounting surface is capable of
supporting the LED light fixture.
3. Locate position where the LED light fixture should be
mounted.
4. Use the keyhole tabs on the end of the LED light fixture
to mark the appropriate screw hole locations. Pre-drill
holes in the mounting surface with a 1/16" (1.5mm
drill bit for soft woods and a 3/32" (2.4mm) drill bit
for hard woods. Since mounting is via keyholes, the
screw heads should protrude approximately 1/8"
(3.2mm) beyond surface.
5. After installing mounting screws (included), secure the
LED light fixture to mounting surface via keyholes. See
Figure 2 and Figure 3.
6. Your line cord has a molded plug on one end and a
link connector at the other end. The link connector
plugs into your LED light fixture. The second cord
provided is a linking cord with link connectors on both
ends. This is used to connect your LED light fixture to the
next LED light fixture in your chain. Link adjacent LED
light fixtures only. See Figure 4 to see how the link
connectors are intended to be used.
7. Attach the quick-connect power cord with the plug and
3-pin quick connector to the LED light fixture closest to
the outlet. See Figure 4 and Figure 5.
8. Plug LED light fixture into a 120VAC 60Hz outlet.
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit http://bit.ly/2WUFkLh
FIGURE 1
CABINET
COUNTER TOP
FIGURE 2
FIGURE 3
INSERT
SLIDE
2 Pin
3 Pin
ELECTRICAL CORD CAN BE ROUTED AROUND
CORNERS TO SUIT THE INSTALLATION
9. This LED light fixture comes with a HIGH/OFF/LOW
switch, allowing you to select a high-power task light
level or a low-level ambient light.
SELECTING LIGHT COLOR TEMPERATURE
The LED light fixture allows you to select from a soft white
light (2700K), a cool white light (4000K) or daylight (5000K)
correlated color temperature (CCT). To select your CCT, simply
use the 3-position switch: SW (Soft White), CW (Cool White),
DL (Daylight). Please note that the switch only controls the
color temperature for a single fixture. It does not control other
connected fixtures.
INSTALLATION INSTRUCTIONS FOR ATTACHING ADDITIONAL LED
LIGHT FIXTURES AT A LATER DATE
If you desire additional LED light fixtures for your system after the initial installation, you may
attach them as needed (sold separately) by following these instructions. Keep in mind the
maximum linking distance between LED light fixtures is 18". In addition, make sure not to exceed
the 40 LED light fixtures per line cord limit for your total installation.
CAUTION: DO NOT ATTEMPT TO ATTACH ADDITIONAL LED LIGHT FIXTURES TO YOUR
EXISTING SYSTEM WITHOUT UNPLUGGING THE LINE CORD FROM THE ELECTRICAL
OUTLET OR DISCONNECTING THE ELECTRICITY AT THE ELECTRICAL SERVICE PANEL.
A. Install additional LED light fixtures following steps 1-5 of the mounting instructions.
B. Once installed, attach the line connector between the last LED light fixture (previously
installed) and the new one. See Figure 4 to see how the 2-pin and 3-pin plugs are intended
to be used.
C. When adding LED light fixtures to an existing system of linked LED light fixtures, the line
cord (with the power plug) is not needed. Only the first light fixture in the chain needs to be
connected to power with the line cord. Please note that the switch only controls a single LED
light fixture. It does not control other linked LED light fixtures.
D Additional linking cords can be purchased on Amazon, byjasco.com, or through our
Customer Care Center at 1-855-698-8324, part number 47167 (12in.), 47168 (18in.),
47169 (24in.), 47170 (36in.), 47172 (48in.), 47171 (60in.), 47173 (120in.).
CLEANING INSTRUCTIONS Your LED light fixture is made from quality materials that will last for many years with minimum
care. When cleaning, make sure you have unplugged your LED light fixture and have allowed
sufficient time for the unit to cool to room temperature. You should clean the housing and lens
using a soft, damp cloth. DO NOT USE chemicals to clean your LED light fixture as this could
damage or disable the LED light fixture. You should plug your LED light fixture back in only after
the light fixture has thoroughly dried.
FIGURE 4
3 Pin
3 Pin
2 Pin
FIGURE 5