Idiomas disponibles
Idiomas disponibles
VII.
SUGGESTED SPARE PARTS TYPE 2 OVENS
Following quantities for each oven:*
• One Heating Element
• One Thermostat Kit
*For quantities of ovens exceeding 10, we suggest providing approximately 20% more of the above quantities of spares as sufficient for day
to day operation.
For overseas operation we suggest a minimum of 30% more for spares.
Phoenix International, Inc. warrants its products against defects in mate-
rial and workmanship. The company will, at its discretion, repair or
replace any properly installed Phoenix International manufactured prod-
uct which fails under normal operating conditions within one year from
date of receipt. Contact the factory for return authorization before return-
ing the product to Phoenix International freight prepaid. If our inspection
confirms that the product is defective under terms of this warranty, it will
be repaired/ replaced and returned freight prepaid.
AWS
(Type)
Cellulose
EXX10
EXX11
EXX20
Titania
EXX12
EXX13
EXX14
Iron Powder M.S.
EXX24
EXX27
Iron Powder Low Hydrogen
EXX18
EXX28
Low Hydrogen
EXX15
EXX16
Low Hydrogen High Tensile
EXXX15
EXXX16
EXXX18
Stainless
EXXX-15
EXXX-16
Inconnel
Monel
Nickel
Hard-Surfacing
Brasses
Bronzes
Granulated or
Agglomerated Flux
Flux Cored Wire
EXXT-1
EXXT-2
EXXT-5
EXXT-G
Note: Proper redrying temperatures depend upon the electrode type and its condition. Contact your electrode
manufacturer for specific instructions involving critical operations. Phoenix International, Inc. does not accept liabil-
ity for damage to electrodes and/or welded products resulting from the use of this table. Temperatures and times
shown are recommended and are not guaranteed to be correct.
Phone (414) 973-3400 • Fax (414) 973-3210 • www.phx-international.com • [email protected]
REV 01/07
Guide to Electrode and Flux Stabilization
eliminate expensive rework & protect welding profits
Air Conditioned Storage
Before Opening
RH=Relative Humidity
70 - 120ºF
(21 - 49ºC)
50% Max. RH
70 - 120ºF
(21 - 49ºC)
50% Max. RH
70-120ºF
(21-49ºC)
50% Max. RH
70-120ºF
(21-49ºC)
50% Max. RH
40-120ºF
(4.5-49ºC)
60% (+/- 10) Max. RH
40-120ºF
(4.5-49ºC)
60% (+/- 10) Max. RH
40-120ºF (4.5-49ºC)
60% (+/- 10) Max. RH
40-120ºF (4.5-49ºC)
60% (+/- 10) Max. RH
40-120ºF
(4.5-49ºC)
60% (+/- 10) Max. RH
Phoenix International, Inc.
• One Power Cord
• One Voltage Selector Switch Kit
• One Indicator Light Kit
This warranty applies only to Products sold by Phoenix International, Inc.
and specifically excludes installation or de-installation labor, transporta-
tion, or equipment of another manufacturer used in conjunction with
Phoenix International products. No other warranty, expressed or implied,
exists beyond this warranty declaration.
Phoenix constantly strives to improve its products and therefore reserves
the right to change design, materials, and specifications without notice.
After Exposure to Moisture a Sufficient
DryRod Oven
Amount of Time to Affect Weld Quality
Holding Temperature
After Opening
Recondition Step #1
100-120ºF
(38-49ºC)
Recommended
180-230ºF
100-120ºF
(82-110ºC)
(38-49ºC)
1/2 Hour
180-230ºF
100-120ºF
(82-110ºC)
(38-49ºC)
1/2 Hour
180-220ºF
250-300ºF
(82-104ºC)
(121-149ºC)
1- 1/2 Hour
180-220ºF
250-300ºF
(82-104ºC)
(121-149ºC)
1- 1/2 Hour
180-230ºF
150-200ºF
(82-110ºC)
(66-93ºC)
1/2 Hour
150-200ºF
(66-93ºC)
Recommended
100-200ºF
Contact Manufacturer for Specific
(38-93ºC)
250-300ºF
Contact Manufacturer for Specific
(121-149ºC)
8711 West Port Avenue • Milwaukee, WI 53224 USA
•
Rebake Step #2
Not
Not
Recommended
250-300ºF
(121-149ºC)
1 Hour
400-500ºF
(204-260ºC)
1/2 Hour
650-750ºF
(343-399ºC)
1 Hour
500-600ºF
(260-316ºC)
1 Hour
Not
Recommended
Not
Not
Recommended
Temperatures
Temperatures
N5610455B-6
