SAFETY INSTRUCTIONS
WARNING! User must read the product manual to
fully understand this product prior to use, and follow
all safety instructions as outlined in the Worx AIR
Operator's Manual.
CAUTION!The user must wear the appropriate
clothing and safety goggles when operating this
product. Be aware of all bystanders, pets and objects in a
close proximity.
•
DO NOT operate blower and attachments when
fatigued.
•
DO NOT overreach or stand on unstable support. Keep
good footing and balance at all times.
•
Never direct airflow towards bystanders. Always be
aware of the direction that the debris will be thrown.
•
Use a face filter mask to avoid breathing dust and
debris.
WARNING: This product can expose you to
chemicals including lead and Di(2-ethylhexyl)
phthalate (DEHP) which are known to the State of
California to cause cancer and birth defects or other
reproductive harm. For more information go to www.
P65Warnings.ca.gov.
COMPONENT LIST
1.
GUTTER TUBE NOZZLE (QUANTITY OF 1)
2.
GUTTER TUBE EXTENSION (QUANTITY OF 3)
3.
GUTTER TUBE ADAPTOR (QUANTITY OF 1)
4.
GUTTER TUBE CONNECTOR (QUANTITY OF 1)
5.
UNIVERSAL ADAPTOR
6.
BLOWER TUBE ADAPTOR
ASSEMBLY AND OPERATION
1. Attach the Gutter kit as shown in Fig. A1 (for Worx
TURBINE, TRIVAC models and other brands blowers),
A2 (for WG545 models), A3 (for WG543 models):
Connect the (1, 2, 3) components by screwing together.
Snap the (3, 4, 5) or (3, 4, 6) components together, and
then tighten the screw (Fig. A4).
2. Assembling the Gutter Tube Adaptor
Fit the gutter tube adaptor to the motor housing as shown
in Fig. B1. Then tighten the screw. (Fig. B1.1) Check the
gutter tube adaptor is firmly secured.
3. Assembling the Universal Adaptor
(1) Place the fabric side of the Universal Adaptor over the
Blower Outlet and slide it on as far as possible (B2).
Worx TURBINE
models-Place the fabric side of the
TM
Universal Adaptor over the outlet of the Fan Housing
and slide it on as far as possible(B2.1).
GUTTERPRO Universal
Gutter Cleaning Kit
Worx TRIVAC
Universal Adaptor over the Vacuum Outlet and slide it
on as far as possible (B2.2). Before operation, flip the
blow/vac switch into the vacuum mode.
PLEASE NOTE: Items can be vacuumed through the
TM
vac inlet and pass through or become clogged within
the gutter kit. Please keep the vac inlet away from
objects while using the gutter kit.
(2) Check to make sure the strap is threaded through the
locking mechanism. Then pull to tighten the strap
(B3). Increase the tension by pulling the latch up and
down to tighten (B4). To loosen, simply press the two
outside latches down and then pull the strap out from
other side (B5).
(3) Test that the Universal Adaptor will not slide off of the
blower outlet.
(4) If further tightening is needed, then pull the middle
latch up and down until the adaptor is tight. Please
recheck if it will slide off of the blower outlet. Realign
and repeat these steps if needed (B4). To loosen,
simply press the two outside latches down and then
pull the strap out from other side (B5).
PLEASE NOTE: The Universal Adaptor may have space
between the Blower Outlet and Adaptor Outlet after
installation.
To remove the adaptor, simply press the two outside
latches down and loosen the strap to remove it from the
Blower Outlet (B5).
NOTE:
Use only enough Gutter Tube Extensions to comfortably
reach the inside of the gutter.
4. Assembling the Blower Tube Adaptor (for WG543
models)
(1) Press the Nozzle Release Button to remove the
Airspeed Selector Nozzle from the Blower Tube. (See Fig.
C1)
(2) Slide the Blower Tube adaptor on and make sure it
firmly locks into position. (See Fig. C2, C3)
(3) Attach the Gutter kit.
5. Operate according to Fig. D:
The Gutter Tube Nozzle can be adjusted to any desired
direction by rotating the Gutter Tube Connector as
shown in Fig. E. Gutter cleaning applications will vary. It
is recommended to try various positions to find the most
effective working position for the type of house and gutter
design.
models - Place the fabric side of the
TM
7
EN
