Tabla de contenido
Idiomas disponibles
Idiomas disponibles
short blinks of the connection status indicator every 2 seconds.
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations → Modules/
Addresses → Plus Button [+]
This mode is limited to 5 minutes in software and on the iSH22M device for
safety reasons.
4. After the iSH22M device shows up in the list make sure to click the button
Allow.
The connection status indicator should remain off.
From now on the iSH22M device is ready to use.
Method 2 - Manual Setup
1. Activate AP mode and access the configuration page as described in section
5.
2. Enter the (SSID) in the field WiFi Name and password WiFi password. Enter
the Mordomus Home Name in the field Home Name as defined in Mordomus -
> Configurations -> Connectivity: Mordomus Home Name.
By entering the house name, the fields Mordomus local IP and Mordomus
Port should be left blank.
3. Activate the pairing mode in the Mordomus Software by clicking the Start
inclusion button in the device registration menu.
To reach this menu from the main screen click Configurations → Modules/
Addresses → Plus Button [+]
This mode is limited to 5 minutes in software and on the iSH22M device for
safety reasons.
4. After the iSH22M device shows up in the list make sure to click the button
Allow.
The connection status indicator should remain off.
From now on the iSH22M device is ready to use.
3. Connection Status indicator codes
WPS discovery mode.
Connected to Wifi and searching Mordomus.
Access Point mode for manual configuration.
Connecting to Router.
iSH22M
4. Resetting the device to factory defaults
1. Enter AP mode and access the configuration page as described in section 5.
2. Click on the Button Reset all.
5. Activating AP Mode (Access Point)
1. By means of a non conductive fine tipped tool, press and hold the push-
button on the backside of the iSH22M for at least 12 seconds to activate Access
Point mode. This is signaled by 3 short blinks of the connection status indicator
every 2 seconds.
2. Using a wireless device (Laptop, tablet, smartphone) connect to WI-FI
network SSID iSH22M_1234 using the password 00000000 (eight zeroes).
The last four digits of the SSID are the same as the last four digits of the
device's serial number. This mode is limited to 5 minutes on the iSH22M
device for safety reasons.
3. In the address bar of the browser of the device enter the IP 192.168.4.1 in
order to access the configuration page of the iSH22M.
5.1. Configuration page
The configuration page of the iSH22M allows for a manual configuration of:
WiFi Name
WiFi Password
Mordomus Home Name
Mordomus Local IP
Mordomus port
The Reset all button resets all of the above settings and other configurations to
the factory default values.
This product complies with the Electromagnetic
Compatibility Directive 2014/30/EU.
This product conforms with the EU Directive 2011/65,
RoHS
regarding the restriction of use of certain hazardous
substances in electric and electronic devices.
For EU countries only.
All old electrical and electronic devices must be
separated from normal household waste and disposed
of at designated facilities. For further information
contact your local authorities, waste disposal office or
the shop where you bought the device.
PT
iSH22M – 2 saídas relé Wi-Fi com
medição de energia + 2 entradas
digitais
Características:
•
2 saídas de relé com monitorização individual de consumo.
•
2 entradas digitais.
Aplicações:
•
Controlo de iluminação, aparelhos ou cortinas/estores elétricos.
•
Controlo de dispositivos de baixa tensão.
•
Leitura de teclas de pressão.
Especificações Elétricas:
Tensão de alimentação: 110-240VAC / 24-60VDC.
Frequência de alimentação: 50/60Hz.
Intensidade de corrente máxima por saída: 10A;
Intensidade de corrente máxima total: 16A;
Norma Wi-Fi: Wi-Fi 802.11 b/g/n, 2,4 – 2,5 GHz.
v.1927
http://mordomus.com/m
ordomus/docs/wifi/iSH2
2M.pdf
2/6
Tabla de contenido
