1. Manuales
  2. Marcas
  3. MORDOMUS Manuales
  4. Relés
  5. iSF20
  6. Manual del usuario

MORDOMUS iSF20 Manual Del Usuario

Ocultar thumbs
1
2
3
4
5
6
Idiomas disponibles

Idiomas disponibles

Tabla de contenido

iSF20
iSF20
EN
iSF20 – Wi-Fi 2 ch relay ON/OFF
Features:
•
2 relay outputs.
Applications:
•
2 relay outputs for illumination, switching of sockets, heating,
boilers, motors, lighting, switching of loads in general.
•
Gradual control of one electric shutter, blind or curtain.
Electrical Specifications:
Power supply voltage: 90-250VAC
Power supply frequency: 50/60Hz
Max current per output: 10A
Max total current: 16A
Wireless standard: Wi-Fi 2.4GHz
Physical Specifications:
Dimensions: 53mm X 32mm X 115mm.
Protection degree: IP20, for indoor use.
ATTENTION:
Mordomus shall not be liable for any damages resulting from the
use of our equipment outside the specifications and/or for a purpose
other than that intended.
Do not exceed the output ratings.
Overview:
Push-button for configuration
Connection status indicator
Screw holding terminal cover.
1. Installation
Caution! Before installing the device, make sure that the mains power
is turned off.
1. Turn off mains power.
2. By means of a PH2 screwdriver remove the screw and the terminal cover.
3. Perform the connection according to the respective schematic (illumination or
blind/curtain control).
4. Place the terminal cover again and tighten the screw.
5. Power up.
2. Connection to WI-FI network and enrollment to Mordomus
Method 1 - Automatic Setup (Router must support WPS)
1. Since factory, on powering up the iSF20 is in WPS negotiation mode signaled
by the connection status indicator blinking fast continuously.
Take care not to power up more than one iSFXX or iSHXX device at the
v.1927
http://mordomus.com/
mordomus/docs/wifi/iS
F20.pdf
1/6
Tabla de contenido
loading

Manuales relacionados para MORDOMUS iSF20

Resumen de contenidos para MORDOMUS iSF20

  • Página 1 2. Connection to WI-FI network and enrollment to Mordomus Method 1 - Automatic Setup (Router must support WPS) 1. Since factory, on powering up the iSF20 is in WPS negotiation mode signaled by the connection status indicator blinking fast continuously.

  • Página 2: Características

    This mode is limited to 5 minutes in software and on the iSF20 device for safety reasons. 2. Using a wireless device (Laptop, tablet, smartphone) connect to WI-FI 4. After the iSF20 device shows up in the list make sure to click the button network SSID iSF20_1234 using the password 00000000 (eight zeroes). Allow.

  • Página 3: Visão Geral

    Método 1 - Configuração automática (o router tem de suportar WPS) Modo PA para configuração manual. 1. Desde fábrica, ao alimentar o iSF20 este está em modo negociação WPS sinalizado pelo indicador luminoso de estado de ligação intermitente rápido. A conectar ao router.

  • Página 4: Visión General

    • Control gradual de un motor, persiana o cortina eléctrica. 4. Después de que el dispositivo iSF20 aparezca en la lista, asegúrese de hacer clic en el botón Permitir. Especificaciones eléctricas: Voltaje de alimentación: 90-250VAC;...

  • Página 5: Página De Configuración

    Méthode 1 - Configuration automatique (le routeur doit prendre en charge WPS) 1. Depuis l'usine, à la mise sous tension, l'iSF20 est en mode de négociation Este producto cumple con la Directiva de WPS signalé par le voyant d'état de la connexion qui clignote rapidement en compatibilidad electromagnética 2014/30 / UE.

  • Página 6: Page De Configuration

    Point d'accès. Cela est signalé par 3 clignotements brefs de l'indicateur d'état de la connexion toutes les 2 secondes. Ce mode est limité à 5 minutes dans le logiciel et sur le périphérique iSF20 (Les bips sonores possibles doivent être ignorés).

Tabla de contenido