Fitting The Hedge Trimmer; Removing The Hedge Trimmer; Swivelling The Hedge Trimmer; Mounting The Saw Chain And Blade - FLORABEST FBK 4 A1 Traducción Del Manual De Instrucciones Original

Fitting the hedge trimmer

♦ Start by undoing the screw grip
♦ Push the front boom
motor unit.
♦ The safety lever must click into the locking hole
♦ Press the cover that protects the safety lever
hold it down.
♦ Tighten the screw grip
NOTE
GB
MT
► The assembly of the pole pruner/strimmer/3-section cutting blade/
extension attachment is carried out in the same order.

Removing the hedge trimmer

♦ Undo the screw grip
♦ Press the safety lever
trimmer out of the boom
NOTE
► Disassembly of the pole pruner/strimmer/3-section cutting blade/
extension attachment is carried out in the same order.

Swivelling the hedge trimmer

♦ Release the lock/release
♦ Press the control lever
desired position.
♦ Allow the control lever
(hedge trimmer) .

Mounting the saw chain and blade

WARNING!
► Wear protective gloves! There is a danger of injury from the sharp
cutting teeth.
NOTE
► Pay close attention to the running direction of the saw chain
the blade and at the base plate (pole pruner)
► Depending on wear, the blade
♦ Undo the nut using the open-ended spanner
♦ Remove the sprocket cover
♦ Lay the saw chain
♦ Now fit the blade
♦ Lay the guide rail
tensioner pin in the blade hole
chain over the chain sprocket
♦ Now you can tighten the saw chain
checking the saw chain").
♦ Replace the sprocket cover

Removing the saw chain

♦ You may have to loosen the saw chain
and the saw chain
chain"). Follow these instructions in reverse order.
64
on the boom of the motor unit.
of the hedge trimmer onto the boom
.
downwards and
.
.
and pull the front boom on the hedge
on the motor unit.
.
and swivel the hedge trimmer into the
to click into the recess in the base plate
can be turned.
7)
.
.
over the blade starting at the tip.
and saw chain .
over the blade guide while inserting the chain
. At the same time, lay the saw
.
(see section "Tightening and
and tighten the nut gently.
to remove the blade
(see section "Tightening and checking the saw

Tightening and checking the saw chain

WARNING!
of the
► Wear protective gloves! There is a danger of injury from the sharp
cutting teeth.
♦ Turn the chain-tensioner screw
flat-blade screwdriver
♦ The saw chain
whether the saw chain
NOTE
► A new saw chain

Lubricating the chain

♦ Remove the oil filler cap
♦ Fill the oil tank
♦ The chain lubrication can be increased or decreased using the oil
adjusting screw
♦ Press and then turn the oil adjusting screw
the chain lubrication.
♦ Press and then turn the oil adjusting screw
the chain lubrication.
WARNING!
► Never work without chain lubrication!
If the saw chain runs dry, the cutting equipment may become irrepar-
ably damaged in a short time. Always check chain lubrication and
oil level in the tank before starting work.
NOTE
► Use only saw chain oil. Preferably biodegradable. Do not use waste
oil, motor oil, etc.
► While working, check whether the chain lubrication is working
correctly.
on

Sharpening the saw chain

.
NOTE
► A grinder can be attached to the grinder support
during grinding.
► You will find detailed information on sharpening in the sharpening
set, e.g. from Oregon.
► Alternatively, you can use an electrical saw chain sharpening device
and follow the manufacturer's instructions .
► If you have any doubts about carrying out the work, the saw chain
should be replaced.

Attaching the extension attachment

CAUTION!
■ Do not use the extension attachment/boom
the 3-section cutting blade/strimmer attachment!
NOTE
► Use the extension attachment/boom
heights.
♦ Fit the extension attachment/boom
hedge trimmer/pole pruner. The assembly is carried out in the same
manner as for the attachments described previously.
in a clockwise direction using the
7!
to increase the tension.
must lie against the underside of the blade. Check
can be drawn by hand over the blade
stretches and must be tightened more regularly.
.
with approx. 100 ml of organic chain oil
.
clockwise to decrease
anticlockwise to increase
5^
in combination with
5^
for working at greater
5^
between the motor unit and the
.
6% .
for a secure grip
FBK 4 A1