Warranty Terms - Schulz SFDC11 Manual De Instrucciones

Model
Category Description
Nº
SFDC11 Professional 5" angle
TABLE 1 – TECHNICAL SPECIFICATIONS
OPERATION
OPERATION
ŸFor Angle Grinder of 5" use air treatment unit (FRL) code 926.5054-0.
ŸConnect the air hose to the tool inflow connector. Run the tool for a few
seconds to check if it is running properly;
ŸIf it doesn't run properly, check if the air governor valve outflow is open;
ŸAdjust the pressure rating of the air governor valve to a maximum of 90
PSIG;
ŸSet the lubricator to insert 2-3 drops of oil per minute (SAE 10);
ŸAfter finishing the job, disconnect the air hose and put the tool away in a
safe and appropriate place to avoid any personal injury and/or damage to
the tool;
ŸCheck if the hose is depressurized before disconnecting it from the tool.
Changing accessories:
ŸLoosen the flange using the pin wrench, insert the abrasive disk, place the
flange again, and then retighten it;
ŸUse an open-end wrench to hold the shaft to facilitate the procedure.
ŸSee the Schulz complete line of accessories in our product catalog.
Recommendations:
ŸMake gentle movements while using the grinder on the working surface
and repeat the operation until the desired finish has been attained;
Never use this tool without the proper individual protection equipment;
Ÿ
Never use this tool without cover protection.
Ÿ
MAINTENANCE
MAINTENANCE
The operator/employer shall be responsible for preventive maintenance
assurance based on the requirements described below:
Implement a daily standard operating procedure for tool models that
Ÿ
require lubrication using (SAE 10) oil following the recommended amount
in this user guide
Verify periodically the condition of accessories (grinding wheel, cover
Ÿ
protection, etc.);
In grinders, periodically grease the the bevel pinion and bevel gear with
Ÿ
molybdenum disulfide grease;
Periodically check moving parts in tools;
Ÿ
Periodically check the air network tubing and hoses for any possible leaks,
Ÿ
condensations, and any other harmful substances that could damage
tools;
Periodically check if the pressure throttle is set at 90 psig (6.3 bars).
Ÿ
Spindle Accessories
rpm
thread (size)
11.000 M14 5" / 125mm
Air Operating
Air
consumption pressure
inlet
(cfm / l/seg) (psi / bar)
30 / 14,2 90 / 6,3 1/4"
PRECAUTIONS
PRECAUTIONS
Read the Operating Instructions. Become familiar with all
instructions and warnings before operating any mechanical tool.
Wear Safety Glasses.
It is mandatory to wear Auricular Protection.
Avoid Exposure to Prolonged Vibration.
Maximum operating pressure is 90 PSIG.
Wear Safety Mask.

WARRANTY TERMS

WARRANTY TERMS
1. The warranty of this product covers manufacturing defects for a period of
6 (six) months based on the date of sales invoice from the original
purchaser.
2. The warranty covers authorized technical assistance (SCHULZ Customer
Service Center) provided at our service center replacing parts and
components.
3. The warranty does not cover:
(a) Installation and product cleaning services.
(b) Operational adjustments requested by purchaser.
(c) Damage to product (to the external, internal, and functional parts),
caused by improper sizing, usage from operator, modifications made by
operator in nonconformity to technical specifications, brought on by
external agents, unfavorable weather conditions, improper accessory
usage, deviation from the purpose of the tool, dropping, and
perforations.
(d) Components are not covered in the warranty that degrade through
normal wear and tear; that are effected by the installation and product
utilization, such as: blades, bearings, sealing rings, and other
accessories. The above mentioned items are covered by Schulz S.A. in
cases where the service assistance is brought about by way of
manufacturing defects confirmed by the (SCHULZ Customer Service
Center).
4. The right to the warranty is terminated previous to the standard warranty
period as stated in item 1 if the user does the following:
(a) Does not follow technical and operational recommendations set down in
this User Guide.
(b) Does not submit the product to preventive maintenance procedures as
described in this user guide.
(c) Does not use original Schulz replacement parts.
(d) Does not present the sales invoice issued to the original purchaser.
(e) Submits the product to repairs from non-authorized service centers by
Schulz S.A.
(f) Violates the original product characteristics.
5. No reseller, sales representative, or technical support assistant from
Schulz S.A. is authorized to modify the contents of the terms of this
warranty.
Net
Hose Length
weight
(mm / inch) (mm)
(kg)
10 / 3/8" 1,8 235
Noise
Vibration
level
2
(m/s )
(dbA)
99 4,6