Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Damaging a gas line can lead to explosion. Penetrating a water
line causes property damage or may cause an electric shock.
b.
Release the ON/OFF switch and set it to the off position when
the power supply is interrupted e.g. in case of a power failure
or when the mains plug is pulled.
PRODUCT DESCRIPTION AND SPECIFICATIONS
Read instruction manual before using the tool
Read all safety warnings and all instructions, Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
INTENDED USE
The machine is designed for grinding and sanding applications. The
machine is designed and constructed for use with attachments
supplied by the manufacturer. The machine can only be used for dry
applications without use of water.
Voltage
Power Rating
Frequency
Protection Class
Rated Speed
Tool Max. Diameter
Mounting Bore Size
Mounting Thread Size
Weight
⚠
WARNING: The declared vibration emission level represents the
main applications of the tool. However, if the tool is used for different
applications, with different accessories or insertion tools or is poorly
maintained, the vibration emission may differ. This may significantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take
into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce
the exposure level over the total working period. Identify additional
safety measures to protect the operator from the effects of vibration.
ASSEMBLY
⚠
WARNING: To reduce the risk of serious personal injury, turn the
tool off and disconnect from the power source before making any
adjustments or removing/installing tools or accessories.
AUXILIARY HANDLE
Screw the handle (2) into one of the side holes on the head of the
grinder as shown in Fig. B. Ensure the handle is secure before use.
METAL GUARD
When using a grinding wheel, first install the metal guard (5) over the
collar (10) and rotate the guard on the tool so that the closed side of
the guard always points toward the operator as shown in Fig. C.
Tighten the screw (12) so the guard cannot move out of position.
FLANGES AND WHEELS
Mount the backing flange (7) onto the spindle (9) with the slot
orientated so that it interlocks with the spindle. Fit the disc, ensuring
it seats correctly onto the flange, then screw on the lock nut (8). Press
the spindle lock (6) and tighten the lock nut using the pin spanner (13).
For installation and operation of other Arbortech accessories please
refer to their dedicated instructions.
CHIP CATCHER AND SANDING PAD
When using a Sanding pad, first install the Chip catcher (17) over the
collar (10), then tighten up the auxiliary handle (2) and side screw (18).
Tighten up the sanding pad (16) over the spindle without the backing
flange.
120
V
8.0
A
60
Hz
II
II
2 000 – 11 000
rpm
4 ½" (115)
Inch (mm)
7/8" (22.2)
Inch (mm)
5/8"
-
4.6 (2.1)
lbs (kg)
c.
Do not touch grinding and cutting discs before they have
cooled down. The discs can become very hot while working.
d.
Secure the workpiece. A workpiece clamped with clamping
devices or in a vice is held more secure than by hand.
OPERATION
⚠
WARNING: Always read the safety instructions and applicable
regulations. To reduce the risk of injury, turn the tool off and
disconnect from power source before making any adjustments or
removing/installing accessories
a.
The electric motor has been designed for the voltage stated on
the label. Always check the power supply corresponds to the
voltage marked on the motor.
b.
Always wear correct safety clothing, including ear, eye and lung
protection.
c.
Follow local government safety regulations when working on
materials treated with or containing toxic substances.
d.
Do not use this tool in wet conditions or in the presence of
flammable liquids and gases.
e.
Check tool before using. The grinding disc must be mounted
properly and be able to move freely. Test run the power tool
with no load prior to use. Do not use damaged, out of centre or
vibrating tools.
f.
Do no exert pressure or strain the machine so heavily that it
comes to a standstill. After heavily straining the power tool,
continue to run it at no load for a minute to cool down the
accessory.
g.
Do not touch cutting tools before they have cooled down. The
discs can become very hot while working.
⚠
WARNING: Always use two hands to operate this power tool,
placing the left hand on the auxiliary handle and the right on the tool
body so you can switch the motor on and off at any time. Always use
protective gloves while operating this tool.
Always use dust extraction for sanding application.
Ensure an appropriate speed setting is selected for the application
from the table below. Support and secure the workpiece to prevent
movement and loss of control.
Ensure the machine is running before contacting the work piece.
Approach the workpiece with caution to avoid sudden grabbing and
gently push against it. Hold the grinder at an angle of 15°-30° for
grinding and 5°-30° for sanding, as shown in Fig. D. Move the tool in
the desired direction, keeping contact between the workpiece and the
disc.
Accessory
Speed
Setting
Grinding
5 – 6
Grinding
Disc
Sanding
1 – 3
Sanding wood, metal and other
Pad
materials. Use lower speed with
higher grit sand paper
SWITCHING ON AND OFF
To start the power tool, push the On/Off switch (3) forwards. To lock
the switch, press it down at the front until it latches. To switch off the
tool, release the On/Off switch or, if it is locked, briefly push down the
back of the switch and release.
⚠
WARNING: The tool includes a restart prevention feature, which
prevents uncontrolled restarting after an interruption to the power
supply. To resume operation, switch the tool to the off position and
start the machine again.
5
Application
Tabla de contenido
