Cleaning And Maintenance; Cleaning The Glass; Safety Instructions For The User - Faber GV60TT/10 Manual Del Usuario

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 29
User manual
ENG
2
The hearth can only be installed by a Gas Safe
registered gas fitter/dealer. The
requirements in the Building Regulations
concerning installation will have to be met.
Also consult the installation instructions.
Note: Because the hearth is a source of heat,
air circulation will arise. That is why it is
important that you do not use the hearth
shortly after a renovation. By natural air
circulation moisture and volatile components
from paint, building materials, floor coverings
etc. that haven't set yet, are sucked up.
These components can be deposited on cold
surfaces as soot. The first time you should use
the hearth depends on various circumstances.
Consult your gas fitter on this matter.
2.1

Cleaning and Maintenance

The appliance will have to be cleaned
and serviced and the proper
functioning checked by a gas fitter.
The outside frame of the hearth can
be cleaned with a clean damp cloth.
2.1.1

Cleaning the glass

Dismount the glass according to the
description in the installation
instructions.
Remove the deposit with a clean dry
cloth. If necessary, a special ceramic
cleaning agent can be used.
Note: prevent the making of finger marks on
the glass. These cannot be removed once the
fire has burnt them into the glass!
2.2

Safety Instructions for the user

The appliance has been designed for
atmospheric and heating purposes. This
means that all surfaces of the hearth,
including the glass, can become very hot
(hotter than 100°C). An exception to this
are the bottom of the hearth and the
controls.
If the hearth has been switched off, wait
for at least three minutes before re-
igniting it again.
If the hearth switches off with no
known cause, wait for at least
15 minutes before re-igniting the
hearth again. If this happens
repeatedly, get in touch with your gas
fitter.
The hearth should not be used if:
The glass is damaged or has been
removed.
If the combustion chamber is open.
Don't place any inflammable materials in
the combustion chamber.
Never change the position of the wood
set and never add more decorative
materials, carrara pebbles or grey stones
than have been supplied with the hearth.
If the hearth is switched on, the pilot
flame should always be visible!
Don't place any curtains, clothes,
laundry, furniture or other inflammable
materials in the neighbourhood of the
appliance. The minimum safe distance is
1 meter.
Don't allow children to use the remote
control unit without adult supervision.
We recommend you always put a fire
screen before the hearth if there are
children, old people or persons with
limited mobility present in the same
room.
2.3
First time the fire is operated
Before ignition, remove all stickers,
protective wrappings and, if present, rubber
protective padding from the glass.
Make sure the room is properly ventilated the
first time the hearth is switched on. Burn the
hearth at the highest position for some hours
so that the lacquer coating will have an
opportunity to set and possible vapours
released can be safely removed by
ventilation. Keep children and pets outside
the room during this process!
2.4
Remote control unit – general
remarks
The appliance has been supplied with a
remote control set; this consists of the
remote control unit (fig. 1.1) and the
receiver(fig. 1.2). The receiver as well as the
gas control block (fig.1.3 )are located behind:
a panel in the chimney breast, a drawer
underneath the hearth or behind a frame.
The remote control has been provided
with 3 keys (fig.1.1). All functions of
the hearth can be operated with
these keys.
If the transmission is successful, the
receiver will emit a sound signal.
With the help of the switch knob B
(fig.1.3 )the flame height can be
regulated without operating the
remote control unit.
The dial A (fig.1.3 )should always be
on the ON position. The MAN position
is only intended for service purposes.
When using the thermostat / timer function,
the wall bracket supplied (fig. 2.4/2.5/2.6)
ENG
10 <
<
<
<
Tabla de contenido
loading

Tabla de contenido