Westin Automotive Products 32-1950 Manual De Instrucciones

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-1950 32-1955
32-1970 32-1975
ITEM QTY
1 1 BULL BAR ASSEMBLY
2,3 2 BRACKET, PASSENGER (2) AND DRIVER (3) 1500
4,5 2 BRACKET, PASSENGER (4) AND DRIVER (5) 2500/3500
6 4 RUBBER BUMPER
7 2 PLASTIC PLUG
8 4 3/8-16 X 1.25" HEX HEAD BOLT
9 8 3/8" FLAT WASHER
10 4 3/8" LOCK WASHER
11 4 3/8-16 HEX NUT
12 6 M12-1.75 REVERSIBLE LOCK NUT
13 6 M12 FLAT WASHER
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 SOPORTES
4,5 2 SOPORTES
6 4 PARACHOQUES DE HULE
7 2 TAPONES DE PLÁSTICO
8 4 PERNOS CON CABEZA HEXAGONAL DE 3/8-16 X 1,25"
9 8 ARANDELAS PLANAS DE 3/8"
10 4 ARANDELAS DE PRESIÓN DE 3/8"
11 4 TUERCAS HEXAGONALES DE 3/8-16
12 6 TUERCA REVERSIBLE A PRESIÓN M12-1,75
13 6 ARANDELAS PLANAS DE M12
1 1 LA BULL BAR
2,3 2 SUPPORT, CÔTÉ PASSAGER (2) ET CÔTÉ CONDUCTEUR (3) 1500
4,5 2 SUPPORT, CÔTÉ PASSAGER (4) ET CÔTÉ CONDUCTEUR (5) 2500/3500
6 4 PARE-CHOCS CAOUTCHOUC
7 2 BOUCHONS DE PLASTIQUE
8 4 BOULONS A TETE HEXAGONALE 3/8-16 X 1,25 PO
9 8 RONDELLES PLATES 3/8 PO
10 4 RONDELLES A FREIN 3/8 PO
11 4 ÉCROUS HEXAGONAUX 3/8-16
12 6 ECROU FREINE REVERSIBLE M12-1,75
13 6 RONDELLES PLATES M12
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely
before beginning. NOTE: Westin advises the installer to use a thread lubricant on all of the stainless steel
fasteners.
STEP 2.
NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not required,
but strongly recommended. If local/state laws requires a license plate, license plate relocation kit 32-0055 is
available.
SEE FIGURE 2 FOR 1500 SERIES AND FIGURE 3 FOR 2500/3500 SERIES
NOTE: For 4500/5500 Series. Remove tow hooks by removing the front and rear bolts that go through the
frame. The tow hooks will not be reinstalled.
STEP 3.
Determine passenger and driver brackets and install as shown.
STEP 4.
Attach Bull Bar to brackets using 3/8" fasteners as shown. Leave loose. SEE FIGURE 4.
STEP 5.
Make sure Bull Bar and brackets are properly aligned and tighten all fasteners. Recommended torque values are
17 Ft. Lbs. for 3/8" fasteners and 65 Ft. Lbs. for 12mm fasteners.
LIGHT INSTALLATION: Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension and
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2006-08 DODGE RAM 1500
APLICACIÓN: DODGE RAM 1500, MOD. 2006-08
APPLICATION: DODGE RAM 1500 2006-08
CONTENTS - CONTENIDO
, LADO DEL ACOMPAÑANTE
, LADO DEL ACOMPAÑANTE
2006-2009 DODGE RAM 2500/3500
DODGE RAM 2500/3500, MOD.2006-2009
DODGE RAM 2500/3500 2006-2009
- CONTENU
(2) Y EL CONDUCTOR (3) 1500
(4) Y EL CONDUCTOR (5) 2500/3500
WO:
2
4
1
3 5
TOOLS - HERRAMIENTA
9/16" SOCKET
9/16" WRENCH
19MM SOCKET
18MM SOCKET
RATCHET
TORQUE WRENCH
DADO DE 9/16"
LLAVE DE TUERCAS DE 9/16"
DADO DE 19MM
DADO DE 18MM
MANERAL
LLAVE DE TORQUE
DOUILLE 9/16 PO
CLE 9/16 PO
DOUILLE 19MM
DOUILLE 18MM
CLIQUET
CLE DE COUPLE
75-0608 REVISION E 9/12/11
- OUTILS