Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
SLAL -75-B F
Bi-Fold Sliding Door Hardware
INSTA L L AT ION INST RUC T ION
Contents
1.
Track
2. Carrier
3. Quick Release Plate
4. Pivot Set
5. Bi-Fold Aligner
6. Snugger
7. Pull
8. Bi-Fold Hinge
9. #8 x 3/4" PH SMS
10. #8 x 1" PH SMS
11. #8 x 1 3/4" PH SMS
12. #10 x 3/4" FH SMS
13. #8 x 7/8" FH SMS
1. Sizing Information
Finished Opening/Panel Dimensions
To determine panel width – Panel width = known finished
opening width divided by number of panels, less 1/4"
To determine opening width – Opening width = known
finished panel width plus 1/4", multiplied by number of panels
Door height = 3 1/4" (+/- 1/2") less than finished opening height
2 Door
4-Door
1
1
1
2
1
2
1
2
–
2
1
2
1
2
4
8
–
4
16
36
1
2
3
6
12
24
For the complete list of
Aluminum Sliding Door
Hardware, the most
up-to-date product
information and installation
instructions, scan the QR
code or visit ngp.com.
1-3/4"
1-11/16"
1-3/4" min.
Pivot Hole
Floor
1-3/4" min.
2-1/8" max.
1-3/4" min.
Pivot Hole
5/8" min.
1-1/4" max.
Manuales relacionados para NGP SLAL-75-BF
Resumen de contenidos para NGP SLAL-75-BF
- Página 1 For the complete list of Aluminum Sliding Door Hardware, the most up-to-date product information and installation instructions, scan the QR code or visit ngp.com. SLAL -75-B F Bi-Fold Sliding Door Hardware INSTA L L AT ION INST RUC T ION Contents 2 Door...
- Página 2 2. Install Track and Hardware • L ine up track flush against jamb on guide door side for 2-door, center track in opening for 4-door (Track length should be 1/8" less than opening width) • Place Top pivot bracket and hangers loose in track before securing track with (#8 x 1") screws • Position top pivot bracket center 2 1/8" from jamb and hand tighten • Secure bottom bracket in jamb corner with (#8 x 3/4") screws • Center quick release and pivot plates on door thickness • Mount top and bottom pivot plates 1 3/4" from center to pivot door edge. (Fig 1) • Mount quick release plate 1 1/4" from center to guide door edge (Fig 1) • Secure plates onto door with (#8 x 1 1/2") screws • D rill 3/16" guide hole in center of guide door and secure pull with (#8 x 1 3/4") screw (Fig 1) • To install hinges place doors side by side as if folded. Secure with (#8 x 7/8") screws. (Fig 2) 3.
- Página 3 • S lide jamb bracket carrier in or out to adjust tilt • I nstall aligners in back, about 12" from bottom with (#8 x 3/4") screws. (4 door install only) • I nstall stops between top guide and side jamb furthest from pivot for 2 door and in the middle between the two pairs of doors for 4 doors NGP-SLI-SLAL-75-BF-PRI-0721-A ngp.com NGP MEMPHIS NGP VEGAS 4985 East Raines Road 4584 Calimesa Street...
-
Página 4: Herrajes Para Puertas Corredizas Plegables
Herrajes de Aluminio para Puertas Corredizas, información actualizada de los productos e instrucciones de instalación, escanee el código QR o visite ngp.com SLAL -75-B F Herrajes Para Puertas Corredizas Plegables INST RUCCION ES DE INSTA L ACION Contenido 2 Puertas 4-Puertas 1. - Página 5 2. Instalación de la Guía y Herraje • E n una instalación de dos puertas alinee la guía contra la jamba del lado de la puerta guía. En un sistema de 4 puertas centre la guía en la apertura (la longitud de la guía debe de ser 1/8" menos que el ancho de la apertura) • A ntes de asegurar la guía con los tornillos (#8 x 1"), coloque sin ajustar el pivote de soporte superior y las correderas en la guía, dejándolos sueltos. • P osicione el centro del pivote de soporte superior a 2 1/8" de la jamba y ajuste manualmente. • A segure el soporte inferior en la esquina de la jamba con tornillos (#8 x 3/4") • Centre la placa de liberación rápida y la placa pivotante en el grosor de la puerta • M onte las placas pivotantes superior e inferior a 1 3/4" de distancia del centro del pivote al borde de la puerta. (figura 1) • M onte la placa de liberación rápida a 1 1/4" de distancia del centro de la placa al borde de la puerta guía (figura 1)
- Página 6 2 puertas y en el centro entre los dos pares de puertas para el sistema de 4 puertas. PERNO DE ALINEADORES (SOLAMENTE AJUSTE PARA SISTEMA DE 4 PUERTAS PIVOTANTE NGP-SLI-SLAL-75-BF-PRI-0721-A ngp.com NGP MEMPHIS NGP VEGAS 4985 East Raines Road 4584 Calimesa Street Memphis, TN 38118...