Control Panel; Maintenance And Cleaning; Energy Efficiency. Erp And Eld - Wesen ECO 30 Manual De Instalación

EN
Always:
- Disconnect the device from the electrical supply
- Close the cold water inlet stopcock
- Turn on a hot water tap

CONTROL PANEL

1
2
On-off switch
(1)
(2) ECO Function
Once the water heater is switched on, press the ECO button to adjust the temperature
to 55 ºC. The temperature selected will be shown at the top of the control panel by
an indicator light.
(3) (4) With the water heater switched on, press buttons + or – until you reach the desired
temperature: 35 ºC - 45 ºC - 55 ºC - 65 ºC - 75 ºC.
The selected temperature will be shown at the top of the panel by an indicator light.
Under normal circumstances we recommend using the ECO mode and setting
higher temperatures for intensive use.
The thermostat will automatically disconnect the electrical connection when the
predetermined temperature is reached in both tanks. Once some water has been
used and the temperature falls below the predetermined value, the thermostat will
automatically reconnect the electrical supply.
All WESEN water heaters allow precise and instant adjustment of water tempera-
ture, thereby ensuring significant savings in terms of electrical consumption.
We recommend that you install a thermostatic valve set to a temperature of 39-41 ºC
and a flow rate of 6-8 litres per minute to obtain the best results from the appliance.
This device will protect against burns as the water from the heater can reach 75 ºC
or more. The user should be aware of the risks involved in exposing parts of the body
to excessively high temperatures and take the necessary precautions to avoid them.
SMART FUNCTION
To activate the Smart Function, press buttons + and – simultaneously and keep them
pressed for 3 seconds. The ECO led will flash 5 times. The system will identify your
water usage habits and adjust heating to those times of use in order to minimize
your electrical consumption.
3 and 4
– 8 –

5. MAINTENANCE AND CLEANING

The water heater does not require any special maintenance and can be cleaned with a soft
damp cloth or sponge. Do not use abrasives or detergents.
Anode replacement
This appliance is fitted with a magnesium anode in each of the tanks. It is necessary to
check the state of the anodes on a annual basis, every six months in areas with aggresive
waters, that is to say, waters with excess lime or chloride.
Check the water quality in your town.
The anode rods must be replaced when they show signs of being consumed or highly deg-
radated. We remind you that the anodes protect the device from corrosion.

6. ENERGY EFFICIENCY. ERP AND ELD

The water heater WESEN ECO 30 of the company NIELSEN CLIMA ESPAÑA, S.L. was
tested with a declared load profile of size "S".
This product fulfills and corresponds to the requirements of the Commission Regulation
Standards (No 814/2013) for electric water heaters and achieved a water heating energy
efficiency of 39.4% that corresponds to the water efficiency class
wh=
The water heater WESEN ECO 50 of the company NIELSEN CLIMA ESPAÑA, S.L. was
tested with a declared load profile of size "M".
This product fulfills and corresponds to the requirements of the Commission Regulation
Standards (No 814/2013) for electric water heaters and achieved a water heating energy
efficiency of 41.3% that corresponds to the water efficiency class
wh=
The water heater WESEN ECO 80 of the company NIELSEN CLIMA ESPAÑA, S.L. was
tested with a declared load profile of size "M".
This product fulfills and corresponds to the requirements of the Commission Regulation
Standards (No 814/2013) for electric water heaters and achieved a water heating energy
efficiency of 39% that corresponds to the water efficiency class
wh=
The water heater WESEN ECO 100 of the company NIELSEN CLIMA ESPAÑA, S.L. was
tested with a declared load profile of size "M".
This product fulfills and corresponds to the requirements of the Commission Regulation
Standards (No 814/2013) for electric water heaters and achieved a water heating energy
efficiency of 41.8% that corresponds to the water efficiency class
wh=
A
" "
.
B
" "
.
B
" "
.
B
" "
.
– 9 –
EN