Idiomas disponibles
Idiomas disponibles
S S o o u u n n d d S S p p a a C C l l o o c c k k R R a a d d i i o o F F e e a a t t u u r r e e s s
•Dawn simulator using your own lamp
•6 Nature Sounds: Rain Forest, Ocean, Thunder, Summer Night, Rain and Water Fall
•AM/FM radio with alarm and snooze
• Seven gentle-wake options – lamp only, lamp and nature sound, lamp and beep, lamp and radio, nature sound only, radio
only, or beep only
•Easy-to-read clock with blue LED display
•Projection feature projects time on the ceiling in a soothing blue light
•Auto-timer lets you choose how long you listen – 15, 30, 45 or 60 minutes or continuously
•Volume control adjusts the volume of the radio, beep or nature sounds
•Wireless lamp brightness control
A A s s s s e e m m b b l l y y a a n n d d I I n n s s t t r r u u c c t t i i o o n n s s f f o o r r U U s s e e
1. Unpack the product and check to make sure everything is included (Fig. 1).
2. This unit is powered by a DC adaptor, which is included.
3. The battery power is designed only to provide MEMORY BACK-UP for the clock and alarm settings. One 9 Volt
battery (not included) should be inserted into the battery compartment if memory back-up is desired (in the event
of power outages or if the unit is unplugged). However, the time will not be illuminated on the clock display. As
soon as the power supply returns, the display will indicate the correct time.
N N O O T T E E : : Battery must be installed in order for clock memory back-up to operate. In the event of a power failure or
disconnection, if the battery is not installed, the clock and alarm will need to be re-set when power is
restored.
4. To install battery, remove compartment cover from the bottom of the unit. Insert one 9 Volt battery into the
compartment following the diagram. Replace cover and snap into place.
5. Attach the DC adaptor connector to the jack located on the back of the unit (Fig. 4) and insert the adaptor into a
120V household outlet.
6. To use the dawn simulator and to control your lamp from your SoundSpa Sunrise, plug your lamp into the bottom
of the wireless receiver (Fig. 3). Then plug the wireless receiver into a 120V household outlet.
N N O O T T E E : : To lock the wireless receiver prongs into place, push up on the locking device. To unlock, push
down (Fig. 3).
N N O O T T E E : : Consult lamp instructions for light bulb specifications. The SoundSpa Sunrise works with most lamps that
use incandescent or CFL dimming light bulbs. Before purchasing CFL bulbs verify they can be used in
lamps with dimming switches.
S S e e t t t t i i n n g g t t h h e e C C l l o o c c k k
1. Your SoundSpa Sunrise clock is set to a 12 hour clock. If you would prefer a 24 hour clock, press the 12/24
button once (Fig. 4).
2. Press and hold the HOUR button for 2 seconds (Fig. 4). The time will begin to flash
3. While the time is flashing, press the HOUR button until you reach the correct hour. Then press the MINUTE button
(Fig. 4) until you reach the correct minute.
N N O O T T E E : : PM indicator will appear on the left side of the clock face for evening hours (Fig. 7). If the PM indicator is
not illuminated, the hour is set to AM. Be sure to set the time for the correct 12-hour period – AM
(morning) or PM (evening).
N N O O T T E E : : After 5 seconds, the time will stop flashing and it will be set.
4. Press the BACKLIGHT HI/LO button (Fig. 4) to choose between high and low clock LED display brightness.
4
WIRELESS RECEIVER
TIMER
ALARM SET
ALARM MODE
VOLUME
SNOOZE BUTTON
F F I I G G U U R R E E 1 1
F F I I G G U U R R E E 2 2
RAIN
FOREST
OCEAN
THUNDER
ADAPTOR
LAMP CONTROL
PROJECTOR
BUTTONS
RADIO
DISPLAY
F F I I G G U U R R E E 3 3
WATER
FALL
RAIN
SUMMER
NIGHT
5
TUNER
PRONGS
LOCK
UNLOCK
PLUG FROM
YOUR LAMP
