English
ASSEMBLY
2-seater
1. Lay the tabletop upside down on the ground,
using the packaging to protect it.
2. Slide the legs into the frame as shown in the
diagram.
3a. First insert 2 M8x60 bolts with 2 M8 spring
washers through the frame and legs from the
outside until they emerge on the inside.
3b. Now insert a M6x16 bolt on the upper surface,
but do not fully tighten it yet.
3c. Fasten the bolts from step 3a with an M8 spring
washer and M8 nut on each one. Repeat this with
the other leg. Now tighten all the bolts.
4. Remove the warning card before assembling BUT
leave the corrugated spring washers where they
are! (These are vital for the rest of the assembly
process.) Now attach the seats to the legs using
4 M6 lock nuts and 8 M6 corrugated spring
washers as shown on the diagram. Please note:
tighten the bolts securely but do not over-tighten!
Max. torque: 15 Nm.
5. Turn the entire structure over.
3/4/5-seater
1. Lay the tabletop upside down on the ground,
using the packaging to protect it.
2. Slide the legs into the frame as shown in the
diagram.
3. Attach the legs to the frame by inserting 2 M8x60
bolts with 2 M8 spring washers through the
frame and legs on each side, from the outside
until they emerge on the inside. Fasten them
with an M8 spring washer and M8 nut on each
bolt. Repeat for the other legs.
4. If you want to stack the tables, we highly recom-
mend that you affix the stacking stoppers.
5. Remove the warning card before assembling BUT
leave the corrugated spring washers where they
are! (These are vital for the rest of the assembly
process.) Now attach the seats to the legs using
4 M6 lock nuts and 8 M6 corrugated spring
washers as shown on the diagram. Please note:
tighten the bolts securely but do not over-tighten!
Max. torque: 15 Nm.
6. Turn the entire structure over.
Backrest
1. Turn the table the right way up and attach the
backrest and the seats to the legs, using 4 M6
lock nuts, 8 M6 corrugated spring washers and
4 M6 spring washers in each case, as shown on
38 – Virus
the diagram. Please note: tighten the bolts secu-
rely but do not over-tighten! Max. torque: 15 Nm.
2. Position 2 allows more body depth.
Floor fastening
1. Turn the table the right way up. One floor faste-
ning set per leg is sufficient. You should always
affix the floor fastening set to the shortest part of
the leg.
2. Remove the plastic caps from the legs using a
pair of pliers.
3a. Now attach the floor fastening set as shown on
the diagram.
3b. Do not fully tighten the bolts at this point.
4. Mark the places on the floor where the table
legs are to be fastened and drill holes at the
points marked.
5. Use the most suitable materials to fasten the
Virus to the type of floor on which it is to stand.
6. Now tighten all the bolts.
MAINTENANCE
Powder-coated parts
Clean with warm water and a non-abrasive cleaner,
then dry with a soft cloth. Do NOT use abrasive
cleaners or scouring sponges as these may cause
scratches.
MiraClean sponge
Only use the MiraClean sponge when normal cle-
aning with lukewarm water, gentle soap and a soft
sponge is insufficient.
If stubborn stains are still visible after cleaning
(see product manual), these may be removed with
the sponges supplied. Moisten the sponge a little
with ordinary water and rub it over the stains to be
cleaned. Do not rub too hard, as this could cause
matt patches.
There is no need to use detergents. Water alone is
sufficient.
The MiraClean is made of melamine resin and wears
away with use. The sponge is very easy to use and
works up to 26 times more quickly than a traditio-
nal microfibre cloth. The sponge removes the most
stubborn stains with no extra effort.
Do not use on shiny surfaces.
The MiraClean scouring sponge is the solution for
removing stubborn stains such as felt tip, grease,
shoe streaks, limescale marks, coffee and tea. The
