Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Impact drill
Safety Warnings
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Battery tool use and care
a) Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools
that have the switch on invites accidents.
b) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
c) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of
injury and fire.
d) When battery pack is not in use, keep it away from other
Special safety warnings
1. Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
2. Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring. Cutting accessory contacting
a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
3. Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
4. If possible, always use clamps or a vice to hold your work.
5. Always switch off before you put the tool down.
6. Ensure that the lighting is adequate.
7. Do not put pressure on the tool, such that it slows the
motor down. Allow the bit to screw without pressure. You
will get better results and you will be taking better care of
your tool.
8. Keep the area free of tripping hazards.
9. Only use accessory bits in good condition.
10. Before starting, check that there is sufficient clearance
for the bit under the work-piece.
11. Do not touch the bit after operation. It will be very hot.
12. Keep your hands away from under the work-piece.
13. Never use your hands to remove dust, chips or waste
close by the bit.
14. Rags, cloths, cord, string and the like should never be left
around the work area.
15. Support the work properly.
16. If you are interrupted when operating the tool, complete
the process and switch off before looking up.
INSTRUCTION MANUAL
EN
metal objects like paper clips, coins, keys, nails, screws, or
other small metal objects that can make a connection from
one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
e) Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause irritation or
burns.
6) Service
Have your power tool serviced by qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintaine.
17. Periodically check that all nuts, bolts and other fixings
are properly tightened.
18. When using the tool, use safety equipment including
safety glasses or shield, hearing protection, and protective
clothing including safety gloves. Wear a dust mask if the
operation creates dust.
19. WARNING
Some dust created by power sanding, sawing, grinding,
drilling,
and
other
construction
chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
· Lead from lead-based paints.
· Crystalline silica from bricks, cement, masonry products,
arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic
particles.
20. Even when the tool is used as prescribed it is not
possible to eliminate all residual risk factors. The following
hazards
may
arise
in
construction and design:
Damage to the lungs if an effective dust mask is not worn.
Damage to hearing if effective hearing protection is not
worn.
REF. 08762
activities
contains
connection
with
the
tool's
Tabla de contenido
