Tabla de contenido
Idiomas disponibles
Idiomas disponibles
R E A D A N D S AV E T H E S E I N S T R U C T I O N S
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
Your unit must be installed by a qualified, licensed electrician.
PRE-INSTALLATION WIRING
• Check that the electrical supply corresponds to that shown
on the rating sticker of unit. If the dryer is connected to any
electrical supply other than that stated on the rating sticker of
the unit, permanent damage or improper, unsafe operation of
the unit may result.
• Make sure electricity is switched off at the main panel before
installing, maintaining or cleaning this hand dryer. Dryer
must be installed in accordance with current local wiring and
building regulations.
• Do not wire this hand dryer into the lighting circuit. It must be
protected by an independent circuit.
• Dryer is intended to be permanently connected to power
supply, and must be properly grounded.
INSTALLATION INSTRUCTIONS
1. Disconnect the power source previously brought to the hand
dryer location (see pre-installation wiring above).
2. Use the Tamper-Proof Wrench supplied and remove the
Tamper-Proof Bolt on bottom of cover lifting upwards to
remove cover from base plate.
3. If electrical wiring entry is to be made from the rear, remove
the appropriate pre-formed knockout on the base plate.
If entry is to be made from the side, knock out the preformed
area on the right side of cover for your supply connection
using knockout gasket provided. A rigid conduit must be used.
4. Select the appropriate mounting height for dryer (Table 1)
and fastener, as recommended (Table 2). There should
be no obstruction between the hand dryer and the floor.
If mounting over a countertop, distance from counter to dryer
must be 15" (381 mm) minimum.
CAUTION: Do not use Base Plate as a guide when drilling.
Make sure no pipe work (gas, water, air) or any electrical cables
or wires are located directly behind the area to be drilled.
5. Attach Base Plate at the four corners to smooth wall.
Identify the voltage of your dryer from the rating sticker of
the unit. Then connect to a dedicated branch circuit not
exceeding 20 Amp.
TABLE 1
SUGGETSTED MOUNTING HEIGHT
1
from floor to bottom of dryer:
Men
45" (114 cm)
Women
43" (109 cm)
Teenagers
41" (104 cm)
Small Children
35" (89 cm)
Accessible
37" (94 cm)
E X C E L D R Y E R , I N C
3 5 7 C H E S T N U T S T R E E T, E A S T L O N G M E A D O W , M A 0 1 0 2 8
For proper electrical connections, check your local building codes.
1 . 8 0 0 . 2 5 5 . 9 2 3 5
SAFETY
• Troubleshooting and internal maintenance must be performed
by qualified service personnel.
• Do not use any power wash equipment for cleaning on or
near this unit.
• Do not use for drying hair.
• Do not obstruct air inlets or outlets.
6. Use one of 2 knockouts provided for service entry on back of
Base Plate. If using surface wiring use knock out in right side
of cover. Use Knockout Gasket supplied around conduit for
water seal. See Mounting Details.
7. Secure electrical wiring to terminals as indicated by the
schematic affixed to blower housing. An identified ground
connection point is supplied on the Base Plate for your
equipment ground wire. Dryers should be installed per local
code requirements.
8. Carefully replace Cover by inserting top of cover over
bracket and tilting downward. Use Tamper-Proof Bolt
previously removed in step 2.
9. Restore power and test for proper operation. In multiple
installations, make sure the serial number marked on the
inside matches the cover number.
10. Return Tamper-Proof Wrench to owner.
MOUNTING HARDWARE
2
Recommended Fastener (not supplied):
Masonry Wall
Hollow Wall
Wooden Wall
E X C E L D R Y E R . C O M
A D M I N @ E X C E L D R Y E R . C O M
TABLE 2
½" Expansion Sleeve with ¼" Lag Bolt
¼" Wing Type Toggle Bolt
¼" Lag Screw With Washer
9 / 2 0 1 8
2
Tabla de contenido
