Changing The Date And Time; Resetting To Factory Settings - Smartwares SHS-53000 Manual De Instrucciones

For 30 seconds, a remote control can be linked or
unlinked.
4. Perform any of the following actions:
a. Press the ON or Up button to link the remote
control. A beep will sound, the remote control is
now linked.
b. Press the OFF or Down button to unlink the remote
control. A beep will sound, the remote control is
now unlinked.
c. Press the ALL OFF button to unlink all remote
controls. A beep will sound, all remote controls are
unlinked.
6.8. Controlling the heating controller with a
remote control
Perform any of the following actions:
• Press the ON button to switch on the heating
controller.
• Press the OFF button to switch off the heating
controller.
6.9. Unlinking all remote controls via the
heating controller
1. Press and hold the Menu button until "Pro" appears in
the display.
2. Select "UnL" by turning the rotary knob.
3. Press OK.
In the display "UnL" will blink.
4. Press OK to unlink all linked remote controls. Press the
Menu button to cancel.
Please note! This device is compatible with Home
!
Wizard. Home Wizard enables you to operate this
device with an APP on your Smartphone or tablet.
For more information about HomeWizard, visit www.
HomeWizard.com.

6.10. Changing the date and time

1. Press and hold the Menu button until "Pro" appears in
the display.
2. Select "dAT" by turning the rotary knob.
3. Press OK.
The year appears.
4. Turn the rotary knob to set the year.
5. Press OK to confirm.
6. Turn the rotary knob to set the month.
7. Press OK to confirm.
8. Turn the rotary knob to set the day.
9. Press OK to confirm.
10. Turn the rotary knob to set the hour.
11. Press OK to confirm.
12. Turn the rotary knob to set the minutes.
13. Press OK to confirm.
The date and time are now changed. Press the Menu
button to return to the start screen.
6.11. Setting a temperature correction
If you use the heating controller in combination with a
wall thermostat, then the room temperature is measured
at the wall thermostat. It is therefore possible that it is
colder or warmer elsewhere in the room. To compensate
for this, a differential temperature can be set.
For example: your wall thermostat measures 22 degrees
and the heating controller measures 24 degrees, then
you can adjust the heating controller 2 degrees.
This is done as follows:
1. Press and hold the Menu button until "Pro" appears in
the display.
2. Select "tOF" by turning the rotary knob.
3. Press OK.
In the display "0.0 °C" appears.
4. Set the desired offset temperature by turning the
rotary knob.
5. Press OK to confirm.

6.12. Resetting to factory settings

1. Press and hold the Menu button until "Pro" appears in
the display.
2. Select "rES" by turning the rotary knob.
3. Press OK.
In the display "rES" will blink.
4. Press OK to reset the heating controller to factory
settings. Press the Menu button to cancel.
7. Maintenance
• The product is maintenance-free, so do not open it.
The warranty will be voided if you open the product.
• Only clean the outside of the product with a soft, dry
cloth or brush.
• Do not use abrasives, corrosive detergents, agents
containing bleach or solvents to clean the product.
• Check once a month whether the fixing ring is
properly tightened. Tighten the fixing ring if it is loose.
• Replace the batteries if the battery indicator starts
blinking.
Please note! The memory of the product will
!
remain stored for up to 1 minute.
8. Malfunctions
Malfunction Cause
Information on - Batteries
the display is empty
not visible
- Batteries
inserted
incorrectly
The battery icon Batteries are
blinks almost empty
Solution
Replace the
batteries
Insert the
batteries
correctly into
the product
Replace the
batteries.
Attention!The
memory of the
product will
remain stored
for up to 1
minute.
9