GB
1.
Assembly of the front wheels
Place the body with the underside facing up.
Slide a Ø10 washer (A) onto the front axle. Attach a wheel (10) and a washer (A) onto the
axle. Fix the whole thing with a clip (B). Finally, put a cover (11) on the wheel. Repeat this on
the other side.
2.
Mounting the rear axle
2.1
Remove the safety covers at the rear of the underside of the body.
2.2
Insert the axle into the body.
2.3
Place the safety covers and screw them on.
3.
Assembly of the rear wheels
Install the drive motor (9) into the rear axle, connect the motor wire plug with the plug in at the
motor clamp port, and insert the motor into the clamp slot. Put the driving wheel (10) on the
rear axle and slide a washer onto the axle. Fix the whole thing with a clip (B). Finally, put a
cover (11) on the wheel. Repeat this on the other side.
4.
Assembly of the pedals
Install the pedal (12) into the car body and fixed it with 4 screws (C).
5.
Assembly of the rear support
Place the iron sheet (14) as shown and fixed it with screw (C).
6.
Assembly of the steering wheel, the trunk and the rear window
Steering wheel
Connect the cable from the steering wheel to the cable of the dashboard. Install the steering
wheel (3) in the intended position and secure it with the safety screw (D) and nut (E)
Trunk
Install the trunk (6) on the back of car body and fixed it with 2 screws (C).
Rear window
Fixed the rear window (7) on the back of car body and fixed it with 2 screws (C).
7.
Mounting the windshield, the car windows and the wing mirror
Windshield
Insert the windshield (1) in the slot on the car body and fixed it with 2 schrews (C):
Car windows
Install the car windows (4) to the destignated position and fasten it.
Wing mirror
Install wing mirror (5) to the designated position, and fasten it.
8.
Battery connection
Connect all connectors as shown. Only connect plug connections that fit into each other and
take care not to reverse polarity. Make sure that the red cable (plus) and the black cable
(minus) are connected to the respective connectors of the same colour.
9.
Mounting the seat
Push the backrest together with the seat cushion. Place the seat by pushing it from above
into the designated position. Fix the seat with 2 screws (C).
10. Charging Your Vehicle
• The power swich must be turned in OFF position when charging.
• Insert the charger (13) into the socket - the LED lights up green. Connect the charger to
the charging socket on the dashboard.
• The LED on your charger lights up red as long as the battery is being charged. If the LED
lights green again, the battery is fully charged.
• The charge time is between 6 and 7 hours.
• Do not charge the battery more than once within 24 hours.
• Charger and battery heat up during the charging process.
Warning!
• Let the model cool off sufficiently after each use before putting it back into
operation. When using an additional batteries let it cool off for minimum 15 minutes
until the model is operated again. Overheating can damage the electronics or may
result in fire.
• Always disconnect the model from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
model. Inserting the rechargeable model or charger after charging will result in
damage tothe model, charger or the power supply (fire hazard).
Only use in direct supervision of an adult!
To control the vehicle a minimum skill level and caution is needed. Make sure you are familiar with the operation of the model and its characteristics. The model is heavy. This is an
increased risk of injury and damage in the event of loss of control. Avoid any kind of intentional or unintentional collisions with objects or hazards to persons.
Caution!
Always switch off the model immediately after each use. Immediately after each use the battery should be disconnected from the model. The battery can be deeply
discharged by leaving it switched on accidentally or leaving it plugged in. Deep discharge causes the battery to lose power or can be damaged to such an extent that
charging or discharging is no longer possible or the battery can self-ignite during charging or discharging (fire hazard). Never attempt to charge or discharge deeply
discharged batteries. The battery voltage should never fall below 11,9 volts to avoid deep discharge. The fully charged battery has a voltage of approx. 13 Volt. After
use, the intact battery should be fully charged immediately after a cooling phase of at least 10 minutes but at the latest after 12 hours to avoid subsequent deep
discharge by self-discharge. If the battery is not used or stored for a longer period of time, the battery should be checked for voltage (min. 12,3 volts) or damage at
least every 3 months and charged or disposed of if necessary.
6
11
c
11. Functions
a Foot pedal
To move the car, press the pedal down.
To brake or slow down, release pressure from the pedal.
b Shift lever
Changes the direction of the car, Forward - Stop - Backward
IMPORTANT!
Always stop vehicle when changing the speed or direction to avoid damage the
gears and motor.
c. Horn
d
1
4
5
6
7
d. Control board
1
USB
After inserting a USB stick
2
Voltage display
3
Charging socket
4
Light button
With the switch to turn on the lights ON or OFF
5
Previous Music/Volume -
Press these buttons briefly to select the previous song to play.
Press these buttons for 2 seconds and the volume will decrease
6
Music button
7
Next Music/Volume +
Press these buttons briefly to select the next song to play.
Press these buttons for 2 seconds and the volume will increase.
8
Power button
Long press it 3 seconds, turn the vehicle on and off.
Short press it for 1 second, stop the music from the car.
9
High speed button
Change the speed of the car more quickly
10 Low speed button
Change the speed of the car more slowly
11
Bluetooth speaker
Press this button, connect ehe mobile phone and Bluetooth in the car, then the car
can play music from your mobile phone.
12 FM Radio
c
d
a
b
2
3
8
9
10 11
12
