Tabla de contenido
•
Never jump-start a frozen battery, as it could explode.
•
Perform all jump-starting procedures in a safe, dry, well-ventilated area.
•
Do not expose battery to fi re or intense heat since it can explode.
•
Before recycling or disposing of a battery, protect exposed terminals with heavy-duty electrical tape to
prevent shorting (shorting can result in personal injury or fi re).
•
Always wear protective eyewear when using this product. Contact with battery acid can cause blindness
and/or severe chemical burns.
•
Follow these fi rst aid procedures in case of accidental contact with battery acid.
FIRST AID
SKIN:
Wash skin thoroughly if battery acid comes in contact with skin. Seek medical attention
immediately.
EYES:
Flush eyes with cool water for at least ten minutes. Seek medical attention immediately.
CONTACT POISON CONTROL CENTER IMMEDIATELY IF INGESTED.
Never touch battery clamps together or to a common piece of metal. Sparking, explosion, or damage to the
unit can result. Always store the clamps in the appropriate holder on each side of the unit after use.
•
Place this unit as far away from the battery being charged as the charging cables will permit.
•
When using the Portable Power System close to the vehicle's battery and engine, place the unit on a fl at,
stable surface, and keep all clamps, cords, clothing and body parts away from moving parts of the vehicle.
•
Follow these instructions and those published by the battery manufacturer and manufacturer of any
equipment you intend to use near the battery. Pay attention to all hazard precautions on these products
and on the engine before charging.
•
This system is designed to be used only on vehicles with a 12-volt DC battery system. Do
a 6-volt or 24-volt battery system.
•
Remove all jewelry or metal objects that could cause short circuits or react with battery acid. A lead-
acid battery produces a short circuit current high enough to weld a ring or other similar objects to metal,
causing a severe burn.
•
When working on electrical equipment, always ensure someone is nearby to help you in an emergency.
•
Keep a supply of baking soda on hand when working on batteries. Baking soda neutralizes lead-acid
battery electrolyte.
All messages that follow have
NOTICE
property damage.
•
Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started.
Before jump-starting, read the vehicle's owner's manual to confi rm that external-starting assistance is
suitable.
•
Excessive engine cranking can damage a vehicle's starter motor. If the engine fails to start after the
recommended number of attempts, discontinue these jump-start procedures and look for other problems
that may need to be corrected.
•
This Portable Power System is
not designed to be used as a replacement for a vehicle's battery. Do not
attempt to operate a vehicle that does not have a battery installed.
•
After connecting the battery charging clamps to the discharged battery and before turning on the jump-
starter ON/OFF switch, check the power/polarity indicator light on the front of the unit. If the light turns
GREEN, the clamp connections are correct. If the light turns RED and an alarm sounds, the clamp
connections are incorrect and need to be reversed.
•
This Portable Power System is delivered in a partially charged state. Fully charge unit with the supplied
110/120-volt AC charger to the recommended maximum and initial charge time of 36 hours. Thereafter,
an AC typical charge time is 18 to 24 hours when using the AC charger.
•
Do
not exceed the recommended maximum and initial DC charge time of 24 hours using the 12-volt DC
method.
•
Although this unit contains a sealed battery, it is recommended that the unit be kept upright during
storage, use and recharging. To avoid possible damage that may shorten the unit's working life, protect it
from direct sunlight, direct heat and/or moisture.
•
Never allow battery acid to come in contact with this unit.
•
All ON/OFF switches should be in the OFF position when charging the Portable Power System or when
not in use. Make sure all switches are in the OFF position before connecting to a power source or load.
•
Do not leave the compressor unattended while operating. The compressor is designed for short-term
operation only. Operation of the compressor over an extended period of time will cause the compressor
unit to overheat and may cause damage. Allow the compressor to cool down for 10 minutes after
extended periods of continuous operation.
•
Do not use any accessory that is not recommended or provided by the manufacturer.
INTRODUCTION
This Portable Power System has been carefully engineered and manufactured to give you dependable
operation. Please read this manual thoroughly before operating your new Portable Power System, as it
contains the information you need to become familiar with its features and obtain the performance that will
bring you continued enjoyment for many years. Please keep this manual on fi le for future reference.
not connect to
level hazards. Failure to comply could result in
3
Tabla de contenido
