Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 36510F
Wrenches: 16mm
Drill Bits: NONE
1 1 1 1 2 2 2 2
1 1 1 1
Qty. (4)
Hex Bolt – M10 x 1.25 x 30mm CL 10.9
1. Raise vehicle with hoist or ramps for access to underside.
2. While supporting exhaust remove rear hangers and lower exhaust until hitch can be positioned over the
muffler tips and into position aligning slots in hitch with existing weld nuts in the bottom of frame.
3. Loosely install the M10 hex bolts with conical washers, (4) four places, as shown.
4. Tighten all M10 CL10.9 fasteners with torque wrench.
5. Reinstall rear hangers for exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2011, 2012,2015 Cequent Performance Products – Printed in Mexico
Installation Instructions
HYUNDAI TUCSON
KIA SPORTAGE
(Sold separately)
FASCIA
FRAME
EXISTING WELD NUTS
KIA SPORTAGE
Tighten all M10 CL 10.9 fasteners with torque wrench to 42 Lb.-Ft. (57 n*m)
Drawbar Kit:
36001
3500 Lb. (1589 kg) Max Gross Trailer Weight
300 Lb. (136 kg) Max Tongue Weight
Wiring Access Location: SUV1, SUV2 (Tucson)
BOTH SIDES
2 2 2 2
Qty. (4)
Conical Washer – 3/8"
Sheet 1 of 3
36510N
Part Numbers:
36510
90211
06132
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
SUV1, SUV5 (Sportage)
HYUNDAI TUCSON
10-13-15
Form F206 Rev A 5605
1 1 1 1 2 2 2 2
Rev. C
Manuales relacionados para Cequent Performance Products 36510
Resumen de contenidos para Cequent Performance Products 36510
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 36510N 10-13-15 Rev. C z 2011, 2012,2015 Cequent Performance Products – Printed in Mexico Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 36510N 10-13-15 Rev. C z 2011, 2012,2015 Cequent Performance Products - Imprimé au Mexique Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del Estado de Nueva York, V.E.S.C. Regulación V-5 d SAE J684. Hoja 3 de 3 36510N 10-13-15 Rev. C 2011, 2012 Cequent Performance Products - Impreso en México Form F206 Rev A 5605...