Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Vehicle frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75663F
Wrenches: 17mm
Figure B.
View underneath vehicle,
Typical both sides.
Existing sway
bar bracket
Existing nut
1
Qty. (6)
M10-1.25 x 40mm CL 10.9 Hex Bolt
Qty. (6)
3/8" Conical toothed Washer
2
1.
If vehicle is AWD-(All-Wheel Drive), then see Note & Figure B. above. It is important to the proper operation of the vehicle to
reinstall sway bar brackets properly as shown.
2.
If vehicle is AWD then remove sway bar brackets both sides, saving existing nuts.
3.
Lower exhaust by removing (4) exhaust rubber isolators that support muffler and tailpipe from hangers.
4.
Raise hitch into position as shown in Figure A. above and install (3) 10mm bolts and toothed washers per side into vehicle
frame weldnuts. If vehicle is AWD then reinstall sway bar bracket with spacer block supplied between lower vehicle attachment
and sway bracket as shown in Figure B. both sides, using existing nut for lower attachment.
5.
Tighten bolts to proper torque as described below. Raise exhaust and re-attach rubber isolators.
Tighten all M10-1.25 X 40mm fasteners with torque wrench to 42Lb.-Ft. (57 N*M)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2008, 2009 Cequent Performance Products
Installation Instructions
Toyota Venza
Vehicle fascia
Note:
AWD MODELS
Existing vehicle sway-bar brackets must be
removed both sides. Then must be reinstalled with
hitch & spacer blocks, (Item 3), supplied.
Space sway bar
bracket down
with supplied
block.
3
1
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, SUV4
2
3
Qty. (2)
5/16" x 1" x 1-1/2" Block-Spacer, ( AWD vehicles only)
Sheet 1 of 3
Part Numbers:
78235
Max Gross
Trailer WT (LB)
4000 (1816 Kg)
3500 (1589 Kg)
1
2
2
1
Figure A.
75663N
10-26-09
Form: F205 Rev A 5-6-05
75663
87521
44604
(U-Haul)
Max Tongue
WT (LB)
400 (182 Kg)
350 (159 Kg)
Rev. C
Manuales relacionados para Cequent Performance Products 75663
Resumen de contenidos para Cequent Performance Products 75663
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75663N 10-26-09 Rev. C 2008, 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75663N 10-26-09 Rev. C 2008, 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75663N 10-26-09 Rev. C 2008, 2009 Cequent Performance Products Form: F205 Rev A 5-6-05...