Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Conical Washer
EXISTING M12
Teeth side
NUTS
Against hitch
ATTACHMENT
BAR
FRAME
10
BUMPER
BRACKET
EXISTING
BUMPER BRACE
2001-2007 ONLY
HITCH
Figure 2
1. Remove the bottom M14 bolts at the end of the frame that help attach the bumper brackets.
2. Remove the side M12 nuts and bolt plates at the end of the frame. Keep these for re-installation later.
*Bumper bracket still has one bolt per side and will not move.
3. If installing on a 2001–07 model loosen the nuts at the bumper end of the bumper brace to allow the brace to swing away from the frame.
4. Raise hitch into position and loosely install the M14 bolts and conical washers (Item 5 and 3) into the weld nut in the bumper bracket.
5. Place attachment bar as shown and loosely bolt to hitch.
6. If equipped with bumper braces, swing them back into position and reinstall bolt plates removed in step 3. See figure 2.
7. Install all of the remaining fasteners as shown in figure 1 and tighten. Not all fasteners may be used on your application – see below.
VEHICLE WITHOUT BUMPER – Use the extra 1/4 x 1-1/2 x 2 blocks (item 9) and M14 nut (item 4) in place of bumper bracket and weld nut. Use the extra fine thread M14 bolts (item 1) in this
case. In place of the bolt plate fasteners - use (4) M12 bolts (item 6), (8) conical washers (item 7) one inside of frame and one outside of frame, (4) nuts (item 8), and (4) jam nuts (item 8).
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which
has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety
specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. - Printed in Mexico
1 1 1 1 2 2 2 2 3 3 3 3
EXISTING
BOLT PLATE
1 1 1 1 3 3 3 3 4 4 4 4
3 3 3 3
5 5 5 5
1 1 1 1
WITHOUT BUMPER
BRACKET
WITH BUMPER
Figure 1
BRACKET
Tighten all M14 x 2.0 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Tighten all M14 x 1.5 fasteners with torque wrench to 145 Lb.-Ft. (201N*M)
Tighten all M12 x 1.75 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Installation Instructions
PART NUMBERS: 45519, 45719
4 4 4 4
EXISTING
WELD NUTS
8 8 8 8
7 7 7 7
6 6 6 6
BUMPER BRACKET
Sheet 3 of 9
Fastener Kit: 45519F
Hex bolt (Fine thread)
1
(6)
M14-1.50 x 45mm CL10.9
Block
2
(2)
3/8 x 1.50 x 3.00
Washer conical
3
(6)
5/8''
Hex nut (Fine thread)
4
(6)
M14-1.50 CL10
Hex bolt (Coarse thread)
5
(2)
M14-2.00 x 45mm CL10.9
FRAME
Hex bolt
6
(6)
M12-1.75 x 45mm CL10.9
Washer conical
7
(10)
1/2"
Hex nut
EXISTING
8
(10)
M12-1.75 CL10
M12 NUTS
Block
9
(2)
¼ x 1.50 x 2.00
Attachment Bar
10
(2)
*Not in Fastener Kit
Fasteners - Typical
both sides
45519N
6-15-16
Rev. A
Tabla de contenido
