Black and Decker Workmate 225 Type 5 Manual De Instrucciones

Workmate
INSTRUCTION MANUAL
FRONT VISE JAW
MÂCHOIRE AVANT
MORDAZA FRONTAL
RELEASE LEVER
LEVIER DE DÉCLENCHEMENT
PALANCA DE LIBERACIÓN
FOLDING LEGS
PIEDS ESCAMOTABLES
PATAS PLEGABLES
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-54-HOW-TO (544-6986)
IF YOU SHOULD EXPERIENCE A PROBLEM
WITH YOUR BLACK & DECKER PRODUCT,
CALL 1-800-54-HOW-TO (544-6986)
BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No.,
TYPE No., AND DATE CODE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE
CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR
COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
Copyright © 2005 Black & Decker
Cat. No. WM225 Type 5
IMPORTANT SAFETY INSTRUCTIONS
1. Do not load with more than 450 pounds.
2. Do not apply an unbalanced load which could cause the work center to tip over.
3. Do not use the work center as a stepladder or standing platform. Do not use the lower
platform as a step when the work center is in "Workbench" position. The footboard is a
foot REST only.
4. Do not store work center outdoors or in a damp location.
5. Avoid applying excessive force when clamping with the swivel pegs.
6. Be sure that the legs are fully open (for workbench height) and be sure that the table
locks in position.
7. When using a power tool with the work center, follow the safety instructions in the
tool's instruction manual.
8. Always wear safety glasses when operating power tools.
9. An even pressure of the vise jaws on the workpiece is essential. Tighten both crank
handles uniformly.
SAVE THIS MANUAL FOR FUTURE REFERENCE
WARNING: IMPORTANT SAFETY WARNINGS AND INSTRUCTIONS
TO REDUCE RISK OF INJURY:
• Before any use, be sure everyone using this tool reads and understands all safety
instructions and other information contained in this manual.
• Save these instructions and review frequently prior to use and in instructing others.
READ ALL INSTRUCTIONS
ASSEMBLY:
The Workmate ® 225 Type 5 work center comes partially assembled. A standard hammer
is required for assembly. A plastic socket wrench is included. Empty the contents of the
box and identify all components (see Figure 1). Place the frame (A) on the floor in the
position shown in Figure 1. Find the release levers near the front rubber feet on the
sides of the frame. Depress both release levers as shown in Figure 2 and pull up until
you hear the frame lock in place.
VISE JAW BRACKET:
1. Select the vise screws (D) and the pivot nuts (E). Screw one pivot nut onto each
vise screw about halfway as shown in Figure 3, assemble washer (P) on vise screw.
2. Insert the unthreaded end of the vise screws into the frame such that the pivot nuts
are located in the slots on the top of the frame and the unthreaded ends protrude
through the holes in the front of the frame, as shown in Figures 3 and 4.
3. Install the two vise cranks (F) and secure them by driving the pins (N) through the
holes in the cranks and the vise screws. (Align the holes in the vise cranks with the
holes in the vise screws and strike the pins sharply with a steel hammer until they
are flush with the sides of the vise cranks.) See Figure 5.
4. Closely examine the two front top blocks and the two rear ones. Note that the front
blocks do not have a protruding tab on the bottom side where the rear blocks do.
Select the front vise jaw, (B), and the two front top blocks, (K). Place the top blocks
on the rails of the frame as shown in Figure 6.
5. Install the front vise jaw on top of the top blocks so that the small holes at each end
of the jaw fit down over the posts on the top side of the blocks. With the jaw
positioned as described above insert into the frame as shown in Figure 6, insert two
of the four bolts, (M) into the holes in the jaw and tighten them securely into the
holes in the pivot nut. Use the socket wrench, (J) provided, shown in Figure 1.
NOTE: For clarity, only the left side assembly is shown. Perform all operations
on right side as well.
6. Select the rear vise jaw, (C) and the two rear top blocks, (L). Position the rear top
blocks on the frame rails so that the tab ears in the bottom of the blocks fit into the
key holes of the frame rail. Position the top blocks so their raised posts are toward
the rear of the frame, as shown in Figure 7. Now install the rear vise jaw so that the
small holes in the ends of the jaw fit over the raised posts on the top blocks you just
installed.
7. Insert the remaining two bolts, (M) into the holes in the jaw and through the top
blocks into the raised posts of the vise guides. The holes in the rear blocks are not
threaded so you will feel resistance as you cut threads into them.
®
225 Type 5
REAR JAW
MÂCHOIRE ARRIÈRE
MORDAZA TRASERA
CRANK
MANIVELLE
MANIVELA
SNAP-IN KNOBS
BOUTONS À ENCLENCHER
MANGOS DE LA MANIVELA
FOOTREST (NO STEP)
REPOSE-PIED (PAS UN MARCHEPIED)
DESCANSO PARA LOS PIES (NO ESCALON)
Form No. 630670-00 Feb. '05
8. Snap-in crank handle as shown in Figure 8.
9. To assemble the rubber feet to your Workmate: Turn the unit upside down. Swing
out the four legs to the fully extended and locked position. Align the rubber foot with
the leg as shown in Figure 9. Lightly tap foot into place with a hammer.
CHANGING THE INDEXED POSITION OF THE REAR JAW:
1. Install the rear jaw in 1 of 3 possible indexed "keyhole" positions by indexing the rear
vise jaw into a keyhole in the vise jaw bracket. Secure the rear jaw by sliding it to the
back of the keyhole. As shown in Figure 7.
SWIVEL PEGS:
1. The four supplied swivel pegs can be used in any of the holes in the front and rear
jaws. The pegs are used to extend the dimensions of your Workmate's holding
capacity. (Figure 10)
FIG. 1
D.
VISE SCREW
VIS D'ÉTAU
ESPARRAGO
F.
VISE CRANK
MANIVELLE D'ÉTAU
MANIVELA DE LA PRENSA
H.
SWIVEL PEGS
MORDACHES ORIENTABLES
TOPES GIRATORIOS
K.
FRONT TOP BLOCKS
CALES SUPÉRIEURES AVANT
BLOQUES DE REMATE FRONTALES
O.
RUBBER FEET
BOUT DE CAOUTCHOUC
REGATONES DE GOMA
FIG. 2
Printed in China
FIG. 4
FIG. 6
RELEASE LEVER
LEVIER DE DÉCLENCHEMENT
PALANCA DE LIBERACIÓN
FIG. 8
RELEASE LEVER
LEVIER DE DÉCLENCHEMENT
PALANCA DE LIBERACIÓN
FIG. 10
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and Authorized Service
locations throughout North America. All Black & Decker Service Centers are staffed with
trained personnel to provide customers with efficient and reliable power tool
service. Whether you need technical advice, repair, or genuine factory replacement
parts, contact the Black & Decker service location nearest you. To find your local service
location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-54-HOW-TO.
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge
in either of two ways:
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns
A.
FRAME
CADRE
BASTIDOR
M.
BOLTS
BOULONS
TORNILLOS
FIG. 3
FIG. 5
FIG. 7
FIG. 9
B.
FRONT JAW
MÂCHOIRE AVANT
MORDAZA FRONTAL
C.
REAR JAW
MÂCHOIRE ARRIÈRE
MORDAZA TRASERA
E.
PIVOT NUT
ÉCROU DE PIVOT
TUERCA DE GIRO
G.
CRANK HANDLE
POIGNÉE DE MANIVELLE
ASA DE LA MANIVELA
J.
SOCKET WRENCH
CLÉ À DOUILE
DADO
L.
REAR TOP BLOCKS
CALES SUPÉRIEURES ARRIÈRE
BLOQUES DE REMATE TRASEROS
N.
PINS
CHEVILLES
PERNOS
P.
WASHERS
RONDELLES
ARANDELAS