Whirlpool 7WRS22FDBF Instrucciones Para El Usuario página 29

Tabla de contenido
Idiomas disponibles

Idiomas disponibles

Remove the Doors
WARNING
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.
1. Unplug refrigerator or disconnect power.
2. Open both doors (refrigerator and freezer) and the water filter
cover door. It is not necessary to remove the water filter itself.
3. Remove the base grille by pulling up on the bottom outside
See Graphic 1
corners.
.
4. Disconnect the water dispenser tubing located behind the
base grille on the freezer door side. The dispenser tubing runs
through the door hinge, and must be disconnected in order to
remove the door.
See Graphic 2
Press blue outer ring against the face of fitting and pull the
n
dispenser tubing free.
NOTE: Keep the water tubing connector attached to the
tube that runs underneath the freezer. The door cannot be
removed if the connector is still attached to the tube that
runs through the door hinge.
5. Disconnect the wiring located behind the base grille on the
freezer door side.
See Graphic 3
Remove the wiring clip using a ¹⁄₄" (7 mm) hex-head
n
socket wrench.
Disconnect wiring plugs.
n
6. Close both doors and keep them closed until you are ready to
lift them free from the cabinet.
7. Use a ⁵⁄₁₆" (8 mm) hex-head socket wrench to remove the top
See Graphic 4
left hinge as shown.
IMPORTANT: Do not remove either screw A.
8. Lift freezer door straight up off bottom hinge.
The water dispenser tubing and wiring remain attached to the
freezer door and pull through the bottom left hinge.
NOTE: This may require two people - one to lift the door and
another to feed the water tubing and wiring through the hinge.
IMPORTANT: Rest the door on its side on a soft, clean
surface, such as a towel, blanket or piece of cardboard. This
will help avoid damaging the door, water tubing and wiring.
9. Remove top right hinge as shown.
IMPORTANT: Do not remove either screw A.
10. Lift the refrigerator door straight up off bottom hinge.
IMPORTANT: Rest the door on its side on a soft, clean
surface, such as a towel, blanket or piece of cardboard. This
will help avoid damaging the door.
11. It may not be necessary to remove the bottom hinges to move
the refrigerator through a doorway. Both bottom hinges have
similar construction.
If necessary, disassemble the hinges as shown.
n
Graphic 7
.
IMPORTANT: To aid in door alignment and closing, there
is a shim located between the hinge and the cabinet.
When the hinge is removed, the shim may fall out of
place. If this occurs, set the shim aside so it can be put
back in place when the hinge is reconnected later.
.
.
.
See Graphic 5
See Graphic 6
.
See
Replace the Doors and Hinges
1. Replace both bottom hinges, if removed. Make sure the shim
is between the hinge and cabinet. Tighten screws.
2. Before replacing the freezer door on the bottom left hinge,
feed the wiring with the yellow plug and the water dispenser
tubing through the hinge. Assistance may be needed.
NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door magnets to
hold the doors in place while you are working.
3. Align and replace the top left hinge as shown.
Tighten screws.
4. Reconnect water dispenser tubing and wiring.
IMPORTANT: Do not intertwine the water tubing and wiring
bundles when reconnecting them.
Push tubing into fitting until it stops and the black mark
n
touches the face of fitting.
Reconnect wiring plugs. Reinstall the wiring clip over the
n
grommets. Tighten screw.
5. Replace the refrigerator door by lifting the door onto the
bottom right hinge.
6. Align and replace the top right hinge as shown.
Tighten screws.
7. Replace the ice storage bin (on some models) and any
adjustable door or utility bins.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
.
Failure to follow these instructions can result in death,
fire, or electrical shock.
8. Plug into a grounded 3 prong outlet.
Leveling and Door Closing
Your refrigerator has two front adjustable rollers — one on the
right and one on the left. If your refrigerator seems unsteady or if
you want the doors to close more easily, adjust the refrigerator's
tilt using the instructions below:
1. Move the refrigerator into its final location.
2. Remove the base grille to locate the two leveling screws,
which are part of the front roller assemblies on each side.
See Graphic 8
.
NOTE: Having someone push against the top of the refrigerator
takes some weight off the leveling screws and rollers. This makes
it easier to adjust the screws.
3. Use a ¹⁄₂" (13 mm) hex-head socket wrench to adjust the
leveling screws. Turn the leveling screw to the right to raise
that side of the refrigerator or turn the leveling screw to the left
to lower that side. It may take several turns of the leveling
screws to adjust the tilt of the refrigerator.
NOTE: Both leveling feet should be snug against the floor, and
the rollers should not touch the floor. This keeps the
refrigerator from rolling forward when opening the doors.
See Graphic 4
See Graphic 2
.
See Graphic 3
.
See Graphic 6
WARNING
See Graphic 8
.
.
.
29

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

7wrs22fdbw7wrs25fdbf

Tabla de contenido