Final Check - Beko BBUM12340X Instrucciones De Instalación

1N AC 220-240 V
* Copper bridge * Copper bridge (EN)
If your supply cord type is 3-conductor type,
for 1-phase connection:
- Brown/black = L (Phase)
- Blue = N (Neutral)
- Green/yellow wire = (E)
If your supply cord type is 5-conductor type,
for 3-phase connection:
- Brown = L1 (Phase)
- Black = L2 (Phase)
- Grey = L3 (Phase)
- Blue = N (Neutral)
- Green/yellow wire = (E)
• After completing the wire connections,
close the terminal block cover.
• Connect the power cable to supply power
by routing it so that it will not contact the
product and get squeezed between the
product and the wall.
Prevention against possible fire risk!;
• Ensure all electrical connections are secure
and tight to prevent risk of arcing.
• Do not use damaged cables or extension
cables.
• Ensure liquid or moisture is not accessible
to the electrical connection point.
Placing and securing of the hob
(Figures 5-6-7-8)
• After preparing the installation location of
the appliances, turn the hob upside down
and place it on a flat surface.
• Affix the sealing gasket supplied with the
appliance around the hob so that it shall
be 1-2 mm inside the outer edge of the
glass as shown in Figure 5. Ensure that no
clearance is left between both ends and
between the glass and gasket.
• Screw and secure the mounting springs
supplied with the appliance by engaging
them to their seat on the lower housing
of the hob as shown in Figure 6. (In some
models, these springs may be secured to
the appliance ex-factory.)
3N AC 380-415 V
(Earthing)
(Earthing)
• Turn the hob again and align it with the
worktop and then place it on the worktop.
Cooker shall be placed on the worktop
thanks to the springs, and it shall be easily
secured.
• Ensure that the hob and the worktop are
parallel when you place the cooker on the
worktop. When it is not in parallel, connect
the additional installation clamps supplied
with the appliance as shown in Figure 8.
Figure 8 shows the possible installation
locations of the clamps. (The locations
where the clamps can be attached may
vary depending on the product model. You
can connect according to the mounting
holes on your hob.) Ensure the parallelism
by attaching the clamps to the appropriate
locations. The type and quantity of clamps
supplied with the product may vary
depending on the product model.
Making hob-oven connection and
placing and fixing the oven
(Figure 9a-9b-10)
• Connect the oven to the power supply.
• Slide the oven centered with at least two
persons into the cabinet until half way.
• If your hob type is vitroceramic: The hob
has a socket and a grounding cable to be
connected to the oven. As shown in figure
9a, connect the socket to its slot on the
oven in a way that the colors match. Fix the
grounding cable with the screw shown in
figure 9a.
• If your hob type is induction: The hob
has two socket and a grounding cable to
be connected to the oven. As shown in
figure 9b, connect the sockets to its slot on
the oven. Fix the grounding cable with the
screw shown in figure 9b.
• Place the oven to the cabinet completely.
• Fix the oven to the furniture using the
screws provided. (Figure 10)
• At the end of the installation, check that
the screws are properly tightened and that
the product is firmly fixed. If the oven is not
installed in accordance with the instructions
and the screws are not properly tightened,
there is a risk of tipping during use.

Final check

• After installation, turn on the power supply.
• Read the user manual for the first use of
the appliances.
• Check functions of appliances.
9