Eden World Tour Pro Serie Guia De Inicio Rapido página 8

EDEN | WTP SERIES | WTP600 REAR PANEL FEATURES - 10
13. Stereo Loop Send R: Send your right effect chain signal out from here.
14. Bridge / Stereo mode: Switch between bridge mode and stereo mode here.
15. Cycle Mode: Cycle between available speaker output settings using this switch.
16. DI Volume: Adjust the output level of the DI Signal here.
17. Pre-Send: Take your signal from before the EQ stage here.
18. Pre-Return: Return your signal before the EQ stage here.
19. Ground Lift: Use this switch to lift ground on the DI output signal here.
20. Pre/Post Select: Select where the DI output signal is taken from here.
21. DI Out: Take XLR DI output signal from here.
22. Tuner Out: Take your signal for your tuner here.
23. Stomp: Connect optional Stompware Eden footpedal here to use footswitchable features on the amplifier.
24. X Over: Turn crossover circuit off or on using this switch.
25. X Over Control: Use this control to adjust the crossover point between each amplifier and the Left/Right line level outputs (Bi-Amp
mode only).
World Tour Pro 600 Rear Panel Features
SPEAKER OUTPUTS: The Eden Illuminated Output System used on World Tour Pro amplifiers has been designed by Eden to more
easily allow players to make the right choices with their rig selection simply use the CYCLE button on the rear of the unit to select
the cabinet array you need.
Each mode will change the illuminated color of the socket indicating the correct impedance cabinet to be used.
GREEN: indicates 4 Ohm compatibility, AMBER: indicates 8 Ohm compatibility, RED: indicates not to use this socket.
1. Amp Speaker 1 Output: Depending on selected mode connect the correct impedance cabinet here using a Speakon speaker lead here.
2. Amp Speaker 2 Output: Depending on selected mode connect the correct impedance cabinet here using a Speakon speaker lead here.
1 4 | H I F I D E L I T Y F O R L O W F R E Q U E N C Y
EDEN | WTP SERIES | WTP600 REAR PANEL FEATURES - 10
3. Output Left: Take your left signal output (post loop) to external equipment here.
4. Output Right: Take your right signal output (post loop) to external equipment here.
5. Aux Input: Connect Auxiliary input signal from your MP3 player or other device using 3.5mm jack cable here.
6. Headphones: Connect your headphones using this 3.5mm output (the headphone volume is controlled by the Master volume control on
the amplifier front panel).
7. Stereo Loop Return L: Return your left effect chain signal here.
8. Stereo Loop Return R: Return your right effect chain signal here.
9. Balance Control: Use this control to balance the level of Left/Right signal in the power amp.
10. Stereo Loop Send L: Send your left effect chain signal out from here.
11. Stereo Loop Send L: Send your right effect chain signal out from here.
12. DI Volume: Adjust the output level of the DI Signal here.
13. Cycle: Use this button to switch between cabinet impedance options.
14. Pre-Send: Take your signal from before the EQ stage here.
15. Pre-Return: Return your signal before the EQ stage here.
16. Ground Lift: Use this switch to lift ground on the Di output signal here.
17. Pre/Post Select: Select where the DI output signal is taken from here.
18. DI Out: Take XLR DI output signal from here.
19. Tuner Out: Take your signal for your tuner here.
20. Stomp: Connect optional Stompware Eden footpedal here to use footswitchable features on the amplifier.
21. X Over: Turn crossover circuit off or on using this switch.
22. X Over Control: Use this control to adjust the crossover point between the Left/Right line level outputs.
H I F I D E L I T Y F O R L O W F R E Q U E N C Y | 1 5