Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

IB526101EN
Installation Instructions – Monaco 3000
Instructions d'installation – Monaco 3000
Instrucciones de instalación – Mónaco 3000
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this
product must be performed by a qualified electrician. This product must be installed in accordance
with the applicable installation code by a person familiar with the construction and operation of the
product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or attempting
any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Refer to product label for specific minimum supply conductor requirements.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Fixture may become damaged and/or unstable if not installed properly.
Failure to comply with these instructions may result in death, serious bodily injury and property damage.
DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind
that may arise from the improper, careless, or negligent installation, handling or use of this product.
NOTICE: Green ground wire provided in proper location. Do not relocate.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on
delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be
filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
Safety: This fixture must be wired in accordance with the National Electrical Code and applicable local codes and
ordinances. Proper grounding is required to insure personal safety. Carefully observe grounding procedure under
installation section.
APPLICATIONS: This lighting fixture is designed for outdoor lighting services, and should not be used in area
of limited ventilation or inside high ambient temperature enclosures. It must be stored in a dry location prior to
installation. Do not expose lighting fixture to rain, dust or other environmental conditions prior to installation
and insertion of photo control or shorting cap (if so equipped). Best results will be obtained if installed and
maintained according to the following recommendations. UL requires minimum fixture mounting height of
12 feet.
WARNING
Brand Logo
reversed out of
Lumière
black
INS #
INS #
loading

Resumen de contenidos para Cooper Lighting Lumiere Monaco 3000

  • Página 17: Renuncia De Responsabilidad

    El incumplimiento de estas instrucciones puede provocar la muerte, lesiones corporales graves y daños materiales. RENUNCIA DE RESPONSABILIDAD: Cooper Lighting Solutions no asume ninguna responsabilidad por daños o pérdidas de ningún tipo que puedan derivarse de la instalación, manipulación o uso incorrecto, descuidado o negligente de este producto.
  • Página 18: Instalación

    Destornillador Phillips. • Conectores para cables (se recomiendan los conectores para cables nominales llenos de silicona para uso enexterior) Cubo Cubierta protectora contra residuos (Cuadrada) Cubierta protectora contra residuos (redonda) Fusible (opcional) Figura 1. COOPER LIGHTING SOLUTIONS IB526101EN Instrucciones de instalación...
  • Página 19 (redondo o cuadrado) Como referencia consulte la “Aplicación de la instalación” . Vidrio y junta Figura 3. Mantenga sin residuos los huecos de colocación de Figura 2. tornillos. Esto ayudará a asegurar un sellado completo. COOPER LIGHTING SOLUTIONS IB526101EN Instrucciones de instalación...
  • Página 20 Utilice un conducto ota: Use un compuesto hermético adecuado de sellado gris para (no incluido) conductos a la hora de sellar alrededor de la entrada del conducto (no incluido) Figura 7. Figura 5. COOPER LIGHTING SOLUTIONS IB526101EN Instrucciones de instalación...
  • Página 21 El balasto debe quedar al nivel de sellar alrededor sea la que se muestra, luego de la entrada del del fondo del cubo orientado de realizar las conexiones. conducto (no incluido) como se muestra. Figura 9. Figura 11. COOPER LIGHTING SOLUTIONS IB526101EN Instrucciones de instalación...
  • Página 22 Asegúrese de que el todos los orificios alojamiento de la lámpara de montaje y las esté bien asentado antes de superficies selladas no la instalación Junta/Vidrio tengan residuos antes de instalar Junta/Vidrio Figura 15. COOPER LIGHTING SOLUTIONS IB526101EN Instrucciones de instalación...
  • Página 23 3000-SG (Pantalla antireflejo) 3000-RG Ensamble del (Protector contra balanceo) balasto Vuelva a instalar los tornillos (3X) (esto bloqueará la moldura en la posición). Nivelar al fondo del cubo Figura 17. Figura 19. COOPER LIGHTING SOLUTIONS IB526101EN Instrucciones de instalación...
  • Página 24 Instrucciones de instalación – Mónaco 3000 Ensamble del controlador Montar a los salientes (3X) Figure 19a. Figure 19b. COOPER LIGHTING SOLUTIONS IB526101EN Instrucciones de instalación...
  • Página 25 Garanties et limitation de responsabilité Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions générales. Garantías y Limitación de Responsabilidad Visite www.cooperlighting.com para conocer nuestros términos y condiciones. Cooper Lighting Solutions is a registered trademark. All trademarks are property Cooper Lighting Solutions of their respective owners.