Evolution R15VAC Instrucciones Originales página 8

OPERATING INSTRUCTIONS
WARNING: To reduce the risk of fire or explosion, do not operate
this vac in areas with flammable gases, vapors or explosive dust
in the air. Flammable gases or vapors include but are not limited
to: lighter fluid, solvent-type cleaners, oil-based paints, gasoline,
alcohol or aerosol sprays. Explosive dusts include but are not
limited to: coal, magnesium, aluminium, and grain or gun powder.
Do not vacuum explosive dust, flammable or combustible liquids
or hot ashes. Do not use this vac as a sprayer for any flammable
or combustible liquid. To reduce the risk of health hazards from
vapors or dusts, do not vacuum toxic materials.
CAUTION: To reduce risk of hearing damage, wear ear protectors
when using the vac for extended hours or when using it in a noisy
area. This 15L wet/dry vac is assembled at the factory and ready
for use when you remove it from the packaging. The unit is ready
for dry vacuuming or blowing. After you plug the power cord into
the wall receptacle, turn the unit "ON" by pushing the switch from
position "O" to position "I". The "O" is the "OFF" position and the
"I" is the "ON" position.
POWER TAKE OFF FUNCTION
WARNING: Danger, Risk of injury and damage!
Power take off switch for automatic vacuum. This function allows
for the vacuum cleaner to turn on when you turn on your power
tool, so the unit is not running in between cuts.
NOTE: The socket outlet is only for the connection of power tools
to the vacuum cleaner. Any other use of the socket outlet is not
permitted.
•
Connect the open dust hose from the vacuum cleaner to the
dust port of your power tool.
•
Connect the mains plug of the electric power tool to the
vacuum cleaner plug socket on the main body. (Fig. 1)
•
Connect vacuum cleaner cable to the main switch on wall
socket.
•
Now switch the rocker switch to setting II - Vacuum cleaner
is in the standby mode. (Fig. 2)
• When you turn on your power tool the vacuum will
automatically start up – use the tool as intended to
complete the job.
•
When you turn off the power tool the vacuum clearer will
automatically stop.
•
Setting II power take off is not suitable for 110V
transformers.
www.evolutionpowertools.com
INSTALLING ACCESSORY BRAC
INSTALLING ACCESSORY BRACKE
1.Push the accessory bracket (A) in
1.Push the accessory bracket (A) in the
2.Secure in place using the screws
2.Secure in place using the screws (B).
INSTALLING ACCESSORY BRA
1.Push the accessory bracket (A)
2.Secure in place using the screws
FIG. 1
WET PICK-UP
WET PICK-UP
1. Remove cartridge filter and repla
1. Remove cartridge filter and replace
INSTALLING ACCESSORY BRACKET
2. This wet/dry vac is equipped with
1.Push the accessory bracket (A) in the
2. This wet/dry vac is equipped with a
to cut off the airflow when the liquid
WET PICK-UP
2.Secure in place using the screws (B).
to cut off the airflow when the liquid in t
this happens, turn off vac, unplug th
this happens, turn off vac, unplug the p
1. Remove cartridge filter and rep
know that the float has shut the airfl
2. This wet/dry vac is equipped w
know that the float has shut the airflow
noise becomes higher in pitch due t
to cut off the airflow when the liqui
noise becomes higher in pitch due to in
vary with the rate of pickup.
FIG. 2
this happens, turn off vac, unplug
vary with the rate of pickup.
know that the float has shut the ai
noise becomes higher in pitch due
WET PICK-UP
vary with the rate of pickup.
1. Remove cartridge filter and replace i
2. This wet/dry vac is equipped with a f
to cut off the airflow when the liquid in th
this happens, turn off vac, unplug the po
know that the float has shut the airflow o
noise becomes higher in pitch due to inc
FIG. 3
vary with the rate of pickup.
INSTALLING ACCESSORY BRACKET
1.Push the accessory bracket (A) in the recess.
2.Secure in place using the screws (B).
EMPTY THE TANK
EMPTY THE TANK
EMPTY THE TANK
WARNING!
WARNING!
To reduce the risk of injury from acc
To reduce the risk of injury from accide
the dust tank.
To reduce the risk of injury from a
the dust tank.
1. Remove the power head assemb the dust tank.
1. Remove the power head assembly
WET PICK-UP
FIG. 4
1. Remove the power head assem
clips located on each side of the
EMPTY THE TANK
clips located on each side of the vac
1. Remove cartridge filter and replace it with foam filter w
2. Dump the tank contents into the
2. Dump the tank contents into the pro
WARNING!
2. This wet/dry vac is equipped with a float mechanism w
2. Dump the tank contents into th
to cut off the airflow when the liquid in the tank reaches a
To reduce the risk of injury from acciden
8
this happens, turn off vac, unplug the power cord, and em
the dust tank.
know that the float has shut the airflow off because the su
1. Remove the power head assembly o
noise becomes higher in pitch due to increased motor sp
clips located on each side of the vac
UNLOCK
LOCK
Foam filter
Foam filter
Foam filter
Foam filter
WARNING!
clips located on each side of th
F
Flo
A
B