Black+Decker KX3300 Manual Del Usuario página 8

ENGLISH
Replace the boiler filler cap (7), do not overtighten.
u
Plug the mains plug into the power supply.
u
Reaching temperature (fig. D)
Depending upon the temperature of the water used to fill
u
the reservoir (3), the appliance will take between 6 and 11
minutes to start producing steam.
Refilling the boiler reservoir
Disconnect the appliance from the mains supply.
u
Wait at least 2 minutes for the water to cool and the pres-
u
sure to decrease before removing the boiler filler cap (7).
Warning! The filler cap may be hot during use and during the
cool down period.
Unscrew and remove the filler cap (7).
u
Fill the boiler reservoir (3) with clean tap water. Do not
u
overfill the reservoir past the MAX indicator (maximum 4
litres).
Replace the boiler filler cap (7), do not overtighten.
u
Plug the mains plug into the power supply.
u
Using the wallpaper stripper (fig. E)
Check the state of your plaster before you start work
u
as high temperature steam can loosen weak, porous or
poorly bonded plaster. Plaster is also loosened more read-
ily in areas of cracks, holes or if the steam plate is held in
one position for too long.
You may be able to detect if you have weak plaster by
u
tapping a few areas of the walls with your knuckles. If this
produces a hollow sound, we recommend proceeding only
with extreme care.
In all cases test out the wallpaper stripper on a small area,
u
about 100 cm2 , before starting work properly.
If at any stage finishing plaster is loosened or you hear a
u
crack, do not continue. The wallpaper stripper is safe for
drywall/plaster board surfaces.
Due to the heat generated by this product, it is possible
u
that certain surfaces, ie. carpets, soft furniture, table tops,
cabinets etc., could be marked or damaged. To prevent
this, ensure a wooden board or other barrier is placed
under the boiler to prevent the heat damaging the surface.
Dust sheets or newspapers are not adequate for this
purpose.
For best results, remove wallpaper with a scraper. Scrape
u
off wallpaper in a downward direction (fig. F).
Always wear protection when removing wallpaper from the
u
ceiling. Be careful of condensation collecting in the steam
plate as hot water may drip (fig. G and H). Empty the
steam plate regularly and never use directly above your
head.
8
(Original instructions)
Always place the steam plate in a suitable container when
u
left unattended, even for a few seconds, and keep the
steam plate facing away from you when in use (fig. I and
J).
Storage
Allow the appliance to cool for at least 10 minutes.
u
Empty the appliance.
u
Store the appliance upright in a dry place.
u
Cleaning and Maintenance
Warning! Before performing any maintenance, switch off and
unplug the appliance and allow it to cool.
Occasionally rinse the boiler with tap water until it runs clear.
Do not use chemical additives.
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Connect the green/yellow lead to the earth terminal.
u
Warning! Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage V
AC
Power imput
W
Boiler
I
Capacity
Weight
kg
KX3300 (Type 2)
230
2400
4
2.55