AVS Electronics LED Plus Serie Manual General De Instalación página 14

FUNCTIONS
SA unbalancing
1
STC/LED unbal-
ancing
E
2
N
G
Alarm encod-
ing
3
4 Main Sound
A l t e r n a t i v e
5
Sound
FLASH
6
STC input
7
Enabling
8
Tampers
LED input
9
1 2
POSITIVE
Negative to Negative to
remove give
REMOVE
The SA input can be balanced to negative to give or remove with or without 4k7 Ohm resistance or to
positive to give or to remove with or without 4k7 Ohm resistance.
If the changing of this parameter is done with the siren already powered,
ming the SA input needs to be rebalanced to
Negative to NEGATIVE Positive to
remove TO GIVE remove
The STC and LED inputs can be balanced to negative to give or to remove with or without 4k7 Ohm
resistance or to positive to give or to remove.
MAX. 5
IN 24 Unlimited
HOURS
•
Value 1: the siren blocks the functioning of the Cone and the Flash in rest status after 5 alarms in
within 24 hours and unblocks it after 24 hours from the first alarm
•
Value 2: the siren does not perform any blocking
TONE 1 Tone 2
Tone 1 TONE 2
In steps 4 and 5 the selectable tones of the "Main Sound" (coupled to the SA control) and "Alternative
Sound" (based on the programming coupled to the LED control) passages are programmed. Once the
step is selected, the Modulation can be heard whenever the PB1 button is pushed.
FLASH FOL- 4 0 - m i n u t e
LOWS THE F L A S H o r R e s t o r i n g
A L A R M r e s t o r i n g from STC
STATUS
from STC
•
Value 1: the Flash is restored at the rebalancing of the input that has generated the alarm
•
Value 2: the Flash automatically deactivates after approximately 40 minutes or when the STC input
is rebalanced
•
Value 3: the Flash is deactivated when the STC input is rebalanced
Change of
Red LED Change of
status with
FOLLOWS the status
a Beep and
STC with a Beep
Red LED
•
Value 1: the RED LED is activated at the unbalancing of the STC input and is deactivated at the
rebalancing of the STC input
•
Value 2: a BEEP signals both the unbalancing and the rebalancing of the STC input
• Value 3: the unbalancing of the STC input activates a BEEP and the RED LED, the rebalancing of
the STC input activates a BEEP and deactivates the RED LED
•
Value 4: RED LED and BEEP are not activated by the unbalancing of the STC input
None a
In this step, the tampers to activate or otherwise the T T output are enabled:
•
a: anti-foam t: temperature
GREEN
Alternative status and
LED DOES
sound to Alternative
NOT FOL-
the unbal- sound to
LOW THE
ancing the unbal-
STATUS
ancing LED
•
Value 1: the unbalancing of the LED input activates the GREEN LED, the rebalancing of the LED
input deactivates the GREEN LED
•
Value 2: the unbalancing of the LED input activates the alarm with the Alternative Sound and the
Flash. The rebalancing deactivates the Sound while the Flash behaves based on its configuration.
•
Value 3: simultaneously executes the actions of Value 1 and 2
•
Value 4: the unbalancing of the LED input activates the visualisation of the STC input status with
the RED LEDs
NUMBER OF GREEN LED IMPULSES
3 4 5
Negative to
Positive to remove with
TO
give 4k7 Ohm re-
sistance
restore the correct operation of the siren.
Negative to
Positive to remove with
give 4k7 Ohm re-
sistance
- -
Tone 3 Tone 4 Tone 5
Tone 3 Tone 4 Tone 5
-
B e e p a n d
R E D L E D
are deacti-
vated
t a + t
v: anti-vibration
Green At the un-
balancing,
the red LED
repeats the
last signal-
ling
- 14 -
6 7
N e g a t i v e Positive to
to give with remove with
4k7 Ohm re- 4k7 Ohm re-
sistance sistance
when exiting the program-
N e g a t i v e
to give with
-
4k7 Ohm re-
sistance
- - -
Tone 6 Tone 7
Tone 6 Tone 7
- - -
- - -
v a + v T + V
8
Positive to
g i v e w i t h
4 k 7 O h m
resistance
-
-
Tone 8
Tone 8
-
-
a + t + v