Important Safety Instructions; Specifications - BriskHeat XtremeFLEX BSAT Serie Manual De Instrucciones

IMPORTANT SAFETY INSTRUCTIONS

SAFETY ALERT SYMBOL
The symbol above is used to call your attention to
instructions concerning your personal safety. It
points out important safety precautions. It means
"ATTENTION! Become Alert! Your Personal
Safety is involved!" Read the message that
follows and be alert to the possibility of personal
injury or death.
A person who has not read and understood all
operating instructions is not qualified to operate
this product.

Do not immerse heater in liquid.

Keep volatile or combustible material away
from heater when in use.

Do not use heater in hazardous locations

Keep sharp metal objects away from
heater.

Only qualified personnel are allowed to
connect electrical wiring.

Disconnect all supply power at the source
before making any power connections.

All electrical wiring must follow local
electrical codes.

The end-user is responsible for providing a
suitable electrical disconnect.

The end-user is responsible for providing a
suitable electrical protection device. It is
highly recommended that a GFCI be used.
®
© BriskHeat Corporation. All rights reserved.
®
XtremeFLEX BSAT
Silicone Rubber Heating Tape
Immediate hazards which WILL result in severe
personal injury or death
Hazards or unsafe practices that COULD result in
severe personal injury or death
Hazards or unsafe practices that COULD result in
minor personal injury or property damage

Never handle the heater while it is in
operation; always disconnect the heater
from the power source and allow to cool
prior to handling.

Inspect product before use (see page 6).

Do not use heater with torn or worn
surfaces or other visual damage.

Do not wrap the heater over itself

Do not repair damaged or faulty heaters.

Do not crush or apply severe physical
stress on heater or cord assembly.

Unplug heater when not in use.

Fasten heater to device using approved
methods only.

If spillage of foreign matter onto heater
occurs, disconnect from power source and
clean after heater has been allowed to
cool.

Never operate a heater without an
appropriate heat sink (device being heated
is considered a heat sink).

Make sure there is a uniform fit prior to
energizing. If there are air gaps between
surface to be heated and the heater, hot
spots can occur and could result in
damage due to overheating.
3

SPECIFICATIONS

Operating Conditions:

Maximum Exposure Temperature: 450°F (232°C)

Maximum Humidity: 95% RH
Heater Characteristics:
 
Time Percentage Dial Controller
 
120V Model with NEMA 1-15 Plug
 
240V Model without plug
Width Length Total
in (mm) in (mm) Watts
0.5 (13) 24.0 (610) 72
0.5 (13) 48.0 (1220) 144
0.5 (13) 72.0 (1830) 216
0.5 (13) 96.0 (2440) 288
0.5 (13) 120.0 (3050) 360
1.0 (25) 24.0 (610) 144
1.0 (25) 48.0 (1220) 288
1.0 (25) 72.0 (1830) 432
1.0 (25) 96.0 (2440) 576
1.0 (25) 120.0 (3050) 720
2.0 (51) 24.0 (610) 288
2.0 (51) 48.0 (1220) 576
2.0 (51) 72.0 (1830) 864
2.0 (51) 96.0 (2440) 1152
2.0 (51) 120.0 (3050) 1440
3.0 (76) 24.0 (610) 432
3.0 (76) 48.0 (1220) 864
3.0 (76) 72.0 (1830) 1296
3.0 (76) 96.0 (2440) 1440
3.0 (76) 120.0 (3050) 1440/1800
®
© BriskHeat Corporation. All rights reserved.
®
XtremeFLEX
Silicone Rubber Heating Tape
Power Density: 6.0 watts/in² (0.009 watts/mm²)
Moisture and Chemical Resistant
Suitable for use on Electrically Conductive Surfaces
Part Number Part Number
120VAC 240VAC (No plug)
BSAT051002 BSAT052002
BSAT051004 BSAT052004
BSAT051006 BSAT052006
BSAT051008 BSAT052008
BSAT051010 BSAT052010
BSAT101002 BSAT102002
BSAT101004 BSAT102004
BSAT101006 BSAT102006
BSAT101008 BSAT102008
BSAT101010 BSAT102010
BSAT201002 BSAT202002
BSAT201004 BSAT202004
BSAT201006 BSAT202006
BSAT201008 BSAT202008
BSAT201010 BSAT202010
BSAT301002 BSAT302002
BSAT301004 BSAT302004
BSAT301006 BSAT302006
BSAT301008 BSAT302008
BSAT301010 BSAT302010
4
BSAT