Tabla de contenido
Idiomas disponibles
Idiomas disponibles
WF-MN-MOON_B_SP.qxd
2/20/06
5:23 PM
Page 7
Maintenance:
• To clean the pump:
Unplug the fountain from the electrical outlet. Remove the
pump from the base of the fountain. Use a small brush or
stream of water to remove any debris.
• To keep water clean:
Periodically change the water and clean the product according
to the water condition. Keeping the water clean prevents the
water from becoming sticky and forming micro-organisms.
An algaecide or humidifier/vaporizer treatment can be added
to help keep it clean.
• To clean hard water deposits from
the base or rocks:
Soak the base and rocks in a mixture of vinegar and water to
clean and remove any mineral build-up.
• Keeping the water at an optimum
level:
Add water periodically to keep water level at an optimum level
to avoid shortening the life of the water pump. Fountain
should be "OFF" when refilling to avoid overflow.
NOTE: Never let the water pump run without water.
This will also shorten the life of the water pump.
• Fountain Storage:
When not in use for long periods of time, unplug the fountain
from the electrical outlet, empty the water and store in a cool,
dry place.
Pump Inlet
Front Plate
Flow
Control
Lever
6
Caution:
All servicing of
this fountain must
be performed by
authorized
HoMedics service
personnel only.
Attention:
For best results,
please operate
pump completely
submerged.
Keep the water
level above
the minimum
water level
AT ALL TIMES.
PVC Tubing
Inserts Here
Housing
Impeller
Suction Feet
Troubleshooting:
• If the pump fails to operate, check
the following:
Check the household circuit breaker or plug unit into a different
outlet to make sure the water pump is getting electrical power.
NOTE: Always disconnect the unit from the electrical outlet
before handling the water pump.
Check the water pump discharge and tubing for kinks and
obstructions. Algae build-up can be flushed out in any faucet.
Remove the water pump inlet to access the impeller area.
Turn the rotor to ensure it is not broken or jammed.
Monthly maintenance will add to the life of your water pump.
NOTE: Make sure that the electrical cord loops below the electri-
cal outlet to form a "drip loop". This will prevent water from run-
ning down the cord into the electrical outlet (Fig. 5).
• If the pump is loud, gurgles, spews,
or "burps":
Check the water level to make sure the water pump has enough
water to function.
NOTE: The pump must be completely submerged in water.
• Obtaining a desired water level:
Check the water level daily in the first week to measure the rate of
evaporation. Refill with water as needed.
• If water is splashing outside
the fountain:
Rocks that are hit by water and also touch the edge of the base
will cause water to splash outside of the base and contribute to
the splash factor. Expect some splash to occur as you get the
rocks organized.
NOTE: If splashing continues, rearrange the rocks by moving
them away from the edge of the base. If this does not help,
adjust the flow control valve to a lower setting.
• If water is flowing unevenly:
Check to see if the fountain is on a level surface. Then, run fingers
across fountain surface to help spread the water distribution.
Figure 5
Drip
Loop
7
Grounding Instructions
This product must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for the electric current
to reduce the risk of electric shock. This product is equipped with a
cord having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes
and ordinances.
Grounding Pin
DANGER
Improper connection of the equipment-grounding conductor can
Figure A
result in a risk of electric shock. Check with a qualified electrician
or serviceman if you are in doubt as to whether the product is
properly grounded. Do not modify the plug provided with the
product - if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
This product is for use on a nominal 120-volt circuit, and has a
grounding plug that looks like the plug illustrated in Figure A.
A temporary adapter that looks like the adapter illustrated in Figure B
may be used to connect this plug to a 2-pole receptacle as shown in
Figure C if a properly grounded outlet is not available. The temporary
Tab for
Adapter
adapter should be used only until a properly grounded outlet Figure C
Grounding
Screw
can be installed by a qualified electrician. The green-colored tab
extending from the adapter must be connected to a permanent
Figure B
ground such as a properly grounded outlet box cover. Whenever
the adapter is used, it must be held in place by a metal screw.
Grounded
See Figures D and E below.
Outlet
Figure C
Metal
Screw
Figure D
Figure E
8
Tabla de contenido
