Installing Your Dishwasher; Water Connections - Brandt AX545FXE1 Instalación Y Consejos

Ocultar thumbs Ver también para AX545FXE1:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18

Installing your dishwasher

Freestanding unit
You can use the top as a worktop. We
recommend that you do not place
your dishwasher too close to a heat
source, otherwise you risk damaging
the edging around the top.
Built-in unit
If you are installing your dishwasher
under an existing worktop:
- Remove the board from the top by
unscrewing the two screws located
underneath it (the corner brackets
must remain on the machine).
- Adjust the height of the feet, if
necessary.
- Fix your dishwasher to the worktop
with two screws under the front
corner bracket.
If your worktop is marble or a similar
material, you can fasten your
dishwasher in place at the sides using
two brackets (available from the After-
Sales department or from your
dealer).
You can also build your machine into
a column (raised above the floor).
Top board
Screw
Screw
Front
square
20
Faceable units
You can also match the colour of your
machine to the units surrounding it by
putting a facing on the door.
• Preparation
- Cut a laminated panel to the following
dimensions (in mm): 595 x 585 with a
maximum thickness of 4mm
• Facing the door
- Unscrew the 9 fixing screws from
the facing bracket and remove it;
- Install the previously cut facing
panel;
- Press the bracket hard onto the
panel and retighten the fixing
screws.
Balancing the door (depending on
the model)
Adjust the tension on the springs, if
required, to compensate for the
weight
of
the
facing
panel.
Adjustment is easier with the door
closed.
GB
Installing your dishwasher

Water connections

Important :
check the water's
hardness: all the
information you require
is provided in the
Chapter "Adjusting the
water softener" in your
operating instructions
manual.
Tap: with threaded end, 20/27mm
dia. (3/4" BSP)
Flow: 10l/min. minimum
Pressure: 1 bar to 10 bars
- 1 MPa)
In the event of high pressure, it is
advisable to fit a pressure regulator.
Your Water Company will give you the
necessary information.
Length of the water supply pipe
(standard unit): 1.50m
"Hazardous
Voltage"
symbol
(depending on the model) the hose
is fitted with an electrical device
Connecting the hot water:
Check that your original hose is
designed for connection to the hot
water supply (red marking on the
hose).
If you use a self-
piercing tap, check
that there is sufficient water
flow.
Check that the
0,1 - 1 MPa
seal is fitted
and that the
connection is
tight.
When the tap is on the left-
hand side of the machine, use the
"anti-kinking" hook supplied with the
machine to avoid any risk of the
supply hose* kinking while you are
fitting your dishwasher.
(* For large diameter safety hoses-
(0.1
depending on the model)
If necessary, you can alter the hose's
direction. To do this, loosen the
connection at the bottom left on the
rear of the machine and swivel it as
necessary. Fully tighten the
connection again and check that there
are no leaks.
For dishwashers fitted with safety
hoses:
You must remove the
protective cover (see
the drawing
opposite) to alter the
hose's direction. To
do this, loosen the
two screws (end
fitting T20), remove
the protective cover,
position the
connection in the
direction you wish
and then replace the protective cover.
When you are making a new
installation, you must use a new
hose to connect the machine to
the water supply: you must not re-use
the old hose.
GB
21
Tabla de contenido
loading

Tabla de contenido