Idiomas disponibles
Idiomas disponibles
Tabla de contenido
KIT COMPONENTS
• A) Radio housing • B) Radio brackets • C) A/C control brackets
A
B
Metra. The World's Best Kits.
®
2004-2006
Kia Amanti
KIT FEATURES
• ISO DDIN radio provision
C
MetraOnline.com
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
95-7319
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Assembly
–ISO DDIN radio provision . ....................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-7301
Antenna Adapter: Not required
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 10/26/17 INST95-7319
Tabla de contenido
Manuales relacionados para Metra 95-7319
Resumen de contenidos para Metra 95-7319
- Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 10/26/17 INST95-7319...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Unclip and remove panel surrounding shifter including cup holders. (Figure A) 2. Remove (2) Phillips screws at base of panel surrounding radio and a/c controls. (Figure B) 3. Unclip and remove panel surrounding radio and a/c control. (Figure C) 4. Remove (6) Phillips screws securing 2 Phillips screws on each side radio and a/c control. (Figure D) 5. Remove (4) Phillips screws securing (Figure A) (Figure C) (Figure E) factory a/c control to bracket assembly. (Figure E) Continue to Kit Assembly LOAD (Figure B) (Figure D) 1.800.221.0932 MetraOnline.com... -
Página 3: Kit Assembly
KIT ASSEMBLY ISO DDIN radio provision 1. Attach the corresponding a/c control brackets to the factory a/c control using the factory hardware. (Figure A) Note: The radio housing must be installed first before the a/c control. 2. Secure the radio brackets to the radio with screws supplied with the radio. (Figure B) 3. Slide the radio into the radio opening of (Figure A) (Figure B) (Figure C) the sub-dash. 4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation. 5. Secure the radio housing onto the completed assembly using the factory screws. (Figure C) 6. Reassemble the dash in reverse order of disassembly. REV. 10/26/2017 INST95-7319... - Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 10/26/17 INST95-7319...
- Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 10/26/17 INST95-7319...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Desenganche y quite el panel que rodea el cambiador incluyendo los portavasos. (Figura A) 2. Quite los (2) tornillos Phillips de la base del panel que rodea la radio y los controles de a/c. (Figura B) 3. Desenganche y quite el panel que rodea la radio y los controles de a/c. (Figura C) 2 tornillos Phillips en cada lado 4. Quite (6) tornillos Phillips que aseguran la radio y el controls de a/c. (Figura D) (Figura A) (Figura C) (Figura E) 5. Quite (4) tornillos Phillips que aseguran el control de a/c de fábrica al ensamble del soporte. (Figura E) Continúe con el Ensamble del Kit LOAD (Figura B) (Figura D) 1.800.221.0932 MetraOnline.com... -
Página 7: Ensamble Del Kit
Provisión de radio ISO DDIN 1. Conecte los soportes de control de a/c correspondientes al control de a/c de fábrica usando el hardware de fábrica. (Figura A) Nota: La carcasa de la radio debe instalarse primero antes del control de a/c . 2. Coloque a presión los soportes de radio a la radio con los tornillos suministrados con la radio. (Figura B) (Figura A) (Figura B) (Figura C) 3. Deslice la radio en la abertura de la radio del sub tablero. 4. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y haga todas las conexiones necesarias al radio. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Pruebe el radio para verificar que funcione correctamentea . 5. Coloque a presión la carcasa de la radio sobre el conjunto completado usando los tornillos de fábrica. (Figura C) 6. Vuelva a armar el tablero al revés de como lo desarmó. REV. 10/26/2017 INST95-7319... - Página 8 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 10/26/17 INST95-7319...