Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Limited Warranty
True Innovations seating products are warranted against defects in material and
workmanship while owned by the "Original Purchaser". The term "Original Purchaser"
is defined as that party or entity which purchases True Innovations furniture from an
authorized True Innovations retailer as shown by the original sales receipt. This
warranty does not apply to "as is" or previously owned seating products.
True Innovations warrants its products to be free from defects in materials and
workmanship (normal wear and tear, fading and stretching excepted), for one year
from the date of purchase, except as provided below under the limited warranty.
The exceptions or exclusions to this warranty are as follows:
1. Any warranty claim that is submitted after the limited warranty period, or without
proper proof of purchase will not include the cost of parts, labor, or delivery.
2. This warranty shall not apply to the True Innovations products which have been
subjected to misuse, neglect, alteration, modification, or attachments, either caused
by the original purchaser, shipping, storage, accident, fire, flood, or acts of God.
In the event of a defect in material or workmanship covered by this warranty, True
Innovations will repair or replace, at their discretion, without charge the warranted
furniture within a reasonable amount of time. We reserve the right to require damaged
parts to be returned to us upon request. Natural markings such as scars, brands, grain
variations, wrinkles, color variations, etc. will be considered normal characteristics
and not construed as defects. We cannot warrant leather against scratching or scuffing,
as all leather is subject to blemishes with use.
For claims or questions concerning this warranty, please contact True Innovations
Customer Service department on the web at www.trueinnovations.com. Be prepared
to provide your name, address, daytime phone number, the model and purchase order
number of the product, date of purchase, and the store where it was purchased. True
Innovations requires that the original sales receipt be submitted with all requests to
confirm that you are the original purchaser according to our written warranty.
This warranty gives you specific rights, and you may also have other rights, which vary
from state to state.
All warranties are limited to the original purchaser for normal use which is defined as a
standard work week of forty hours by a person weighing less than 275 lbs.
Should you prefer to speak with a service representative, you may call toll free:
1-800-379-9773, or fax 714-544-5118.
Manufactured by:
LF Products Pte. Ltd.
No.148, Xiazhuang Lane, Changhe Street Scene, Binjiang District, Hangzhou, Zhejiang, China, 310052
Printed in China
Tufted Office Chair
Assembly Instructions
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Customer Service Support: 1-800-379-9773
Lot Number :
Date of purchase :
Model: BHS0025004003
Tabla de contenido
loading

Resumen de contenidos para Better Homes and Gardens BHS0025004003

  • Página 1 True Innovations requires that the original sales receipt be submitted with all requests to Model: BHS0025004003 confirm that you are the original purchaser according to our written warranty.
  • Página 2: Care And Maintenance

    Thank you for selecting one of True Care and Maintenance Innovations seating solutions. Fabric Upholstery: Pay immediate attention to spills and vacuum regularly to maintain It’s True...Fast, Friendly Customer Service appearance. Cleaning products may cause discoloration and should be tested in an inconspicuous location prior to use on the chair.
  • Página 3: Function Instruction

    Parts list Function Instruction Included Parts TO ADJUST TILT TENSION Casters (5) Base (1) Reach under the front center of chair seat and grasp the round black knob. To loosen the tilt mechanism, turn the knob clockwise. This lessens the effort required to rock back and forth.
  • Página 4 Operating Instructions Step 1 Place the Base (2) on a protected surface to avoid scratching components Function Instruction when assembling. Place 5 Star Base (2) upside down and insert Casters (1) into the bottom of the Base (2). TO ADJUST SEAT HEIGHT While seated, lean forward, lifting your body weight from the seat.
  • Página 5 Assembly Instructions Step 3 Align Seat Plate (4) over pre-drilled holes on the underside of the seat Step 6 Position the assembled chair upright with the Seat Plate (4) facing down. cushion with front of seat plate facing the front of the seat cushion. Attach Insert the Gas Lift (3) into the center hole of the Seat Plate (4) and press the Seat Plate (4) to seat cushion using 4 Bolts (A) as shown.
  • Página 6 Assembly Instructions Step 5 Step 4 Turn the partially assembled seat and back onto one side and press With the Back Cushion (6) against the floor, press down firmly on the front of down firmly against one arm to align the side connection holes. Attach the Seat Cushion (5) to align the two rear holes as shown.
  • Página 7: Garantía Limitada

    Todas las garantías están limitadas al comprador original y al uso normal, el que se define como una semana estándar de trabajo de cuarenta horas por una persona que pese menos de 275 libras. : BHS0025004003 Número de modelo ESTE FOLLETO DE INSTRUCCIONES TIENE IMPORTANTE INFORMACIÓN SOBRE Si necesita hablar con un representante de servicio al cliente por favor llame al,1-800-379-9773, o al telefono fax 714-544-5118.
  • Página 8: Nuestro Servicio Al Cliente Es Real...amigable Y Rápido

    Gracias por elegir los productos de Cuidado y mantenimiento True Innovations. Tela de la tapicería: Preste atención inmediata a los derrames y aspire regularmente para mantener el buen aspecto. Los productos de limpieza Nuestro servicio al cliente es real...amigable y rápido pueden causar decoloración y deben ser probados en una ubicación poco visible antes de usarlos en la silla.
  • Página 9: Lista De Partes

    Lista de partes Partes incluidas Instrucciones de las funciones AJUSTE DE LA TENSION EN EL MECANISMO PARA INCLINAR LA Ruedas (5) Base (1) SILLA Busque debajo del asiento de la silla, en la parte central del frente y sujete la perilla negra redonda.
  • Página 10 Instrucciones de uso Paso 1 Ponga la base (2) sobre una superficie protegida para evitar rayar los Instrucciones de las funciones componentes al ensamblarlos. Coloque boca abajo la base (2) en forma de estrella e inserte las ruedas (1) en el fondo de la base (2). CÓMO AJUSTAR LA ALTURA DEL ASIENTO Siéntese, inclínese hacia adelante y levante su...
  • Página 11: Instrucciones De Ensamblaje

    Instrucciones de ensamblaje Paso 3 Alinee la placa del asiento (4) sobre los hoyos preperforados situados en Paso 6 Coloque la silla ensamblada verticalmente, con la plancha del asiento (4) la parte inferior del cojín del asiento con el frente de la placa del asiento hacia abajo.
  • Página 12 Instrucciones de ensamblaje Paso 4 Paso 5 Gire el asiento y el asiento parcialmente ensamblados hacia un lado Con el cojín del respaldo (6) contra el piso, presione firmemente hacia y presione firmemente contra un brazo para alinear los orificios de abajo en la parte delantera del cojín del asiento (5) para alinear los dos conexión laterales.

Tabla de contenido