Lower Guard Function; Additional Safety Instructions; Additional Safety Information - Craftsman CMES510 Manual De Instructiones

English
g ) Use extra caution when sawing into existing
walls or other blind areas. The protruding blade
may cut objects that can cause kickback.

Lower Guard Function

a ) Check the lower guard for proper closing before
each use. Do not operate the saw if the lower
guard does not move freely and close instantly.
Never clamp or tie the lower guard into the open
position. If saw is accidentally dropped, lower
guard may be bent. Raise the lower guard with
the retracting handle and make sure it moves freely
and does not touch the blade or any other part, in all
angles and depths of cut.
b ) Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use. Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up of debris.
c ) The lower guard may be retracted manually
only for special cuts such as "plunge cuts" and
"compound cuts." Raise the lower guard by
retracting the handle and as soon as the blade
enters the material, the lower guard must be
released. For all other sawing, the lower guard
should operate automatically.
d ) Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor. An unprotected, coasting blade will cause
the saw to walk backwards, cutting whatever is
in its path. Be aware of the time it takes for the blade
to stop after switch is released.

Additional Safety Instructions

Use clamps or another practical way to secure and
•
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
• Keep your body positioned to either side of the
blade, but not in line with the saw blade. KICKBACK
could cause the saw to jump backwards (see Kickback
Causes and Related Warnings).
• Avoid cutting nails. Inspect for and remove all nails
from lumber before cutting.
• Always make sure nothing interferes with the
movement of the lower blade guard.
Accessories must be rated for at least the speed
•
recommended on the tool warning label. Wheels and
other accessories running over rated speed can fly apart
and cause injury. Accessory ratings must always be above
tool speed as shown on tool nameplate.
• Always make sure the saw is clean before using.
• Stop using this saw and have it properly serviced if any
unusual noise or abnormal operation occurs.
• Always be sure all components are mounted properly and
securely before using tool.
• Always handle the saw blade with care when mounting or
removing it or when removing the diamond knockout.
4
• Always wait until the motor has reached full speed before
starting a cut.
• Always keep handles dry, clean and free of oil and
grease. Hold the tool firmly with both hands when in use.
• Always be alert at all times, especially during
repetitive, monotonous operations. Always be sure of
position of your hands relative to the blade.
• Stay clear of end pieces that may fall after cutting
off. They may be hot, sharp and/or heavy. Serious
personal injury may result.
• Replace or repair damaged cords.

Additional Safety Information


WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the State
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
Avoid prolonged contact with dust from power
•
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and
wash exposed areas with soap and water. Allowing
dust to get into your mouth, eyes, or lay on the skin may
promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles
away from face and body.

WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19)
during use. Under some conditions and duration
of use, noise from this product may contribute to
hearing loss.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be
caught in moving parts.