Tabla de contenido
Idiomas disponibles
Idiomas disponibles
4.1 READER/VALIDATOR ELECTRICAL CONNECTIONS
Power supply: 8÷30 VDC 3W
MAX
Minimum/maximum cross-section of the
cables is: 0,20÷1,5 mm (24÷15 AWG).
Do not extend the cable supplied with the
external device (5 mt.).
Install the internal device only in a protected
area.
BUS
JP 1
ADDRESS
ADDRESS 1 =
ADDRESS 2 =
ADDRESS 3 =
ADDRESS 4 =
ADDRESS 5 =
ADDRESS 6 =
ADDRESS 7 =
ADDRESS 8 =
6. STAND-ALONE GATE: EXCHANGE OF CODED KEYS WITH ACTUATOR
(JUMPER SETTING)
Set jumpers on Actuator and Stylos Control Unit as per pictures below. Note this configuration is
correct only in case of 1 Stylos (Master) and 1 Actuator (Slave).
For more information about
jumper setting with different
configuration, refer to the
Stylos User Manual available
at app.iseo.com.
Actuator
address 1
7. INSTALLATION ON A METAL PROFILE
Ø 3.2 mm
(max)
Ø 26 mm
Ø 3.2 mm
(max)
9. INSTALLATION WITHOUT THE SPACER
Take
care
to
not
damage the cables
while
installing
the
device.
Check the connections
on section 5 or 6
before
powering
the
device.
GREEN + GREY + SHIELD (or black)
RED
WHITE
BROWN
YELLOW
PINK
BLUE
LOCKBUS
(Communication Channel)
POSITIVE (+) Power Supply
NEGATIVE (-) GND
Control Unit
1
Circuit View
2
J2.
J2.
J2.
J2.
1
2
3
4
3
4
5
JPS
JP
JP
JP
JP
6
4
2
0
JP
JP
6
4
S1
BUS
ADDRESS
Control Unit
P1
L1
L2
P2
LRL
Circuit View
Power supply
8 ÷ 24VDC 25W
J2.
J2.
J2.
J2.
LVO
J P 1
LC H
J P 2
L P W
J P 3
1
2
3
4
JPS
JP
JP
JP
JP
6
4
2
0
S1
Stylos Master
address 0
3.9 x 19 mm
5. ACTUATOR CONFIGURATION:
Switch on the Actuator and check if red led
flashes:
1 time (Lockbus 1) = Reader/Validator.
2 times (Lockbus 2) = Stand-Alone gate.
Change the Lockbus type accordingly to your
configuration, following the next point.
Switch on the Actuator keeping pressed both
buttons simultaneously for 1 sec.
Switch on it again to check if now red led
flashes 1 or 2 times.
J2.
J2.
J2.
J2.
1
2
3
4
If not repeat the procedure.
JPS
JP
JP
2
0
S1
6.1 STAND-ALONE GATE: EXCHANGE OF CODED KEYS WITH ACTUATOR
(EXCHANGE KEYS)
Switch on the actua-
tor keeping pressed
one button for 3 sec.
Actuator
address 1
For more information regarding the exchange of keys, see the Tutorial Video available at
app.iseo.com.
8. INSTALLATION ON A WALL
9.1 INSTALLATION WITH THE SPACER
Take
care
to
damage the cables
while
installing
device.
Check the connections
on section 5 or 6
before
powering
device.
LOCKBUS SELECTION
Control Unit
Circuit View
P1
L1
L2
P2
LRL
Power supply
J2.
J2.
J2.
J2.
1
2
3
4
8 ÷ 24VDC 25W
LVO
J P 1
LC H
J P 2
J P 3
L P W
JPS
JP
JP
JP
JP
6
4
2
0
S1
Ø 5 mm
3.9 x 30 mm
Ø 26 mm
Ø 5 mm
not
the
the
P1
L1
L2
P2
LRL
Power supply
8 ÷ 24VDC 25W
LVO
J P 1
LC H
J P 2
L P W
J P 3
Red led flashing
Switch on the Stylos Control
Unit
keeping
pressed
the
button and wait for the acustic
and light signal, then release it
immediately.
Stylos Master
address 0
5 x 25 mm
Tabla de contenido
