Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Palmgren Operating Manual & Parts List
SAFETY RULES (CONTINUED)
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
PREPARE WORK AREA FOR JOB
• Keep work area clean. Cluttered work areas and work benches
invite accidents.
• Do not use power tools in dangerous environments. Do not use
power tools in damp or wet locations. Do not expose power
tools to rain.
• Work area should be properly lighted.
• Proper electrical receptacle should be available for tool.
Three-prong plug should be plugged directly into properly
grounded, three-prong receptacle.
• Extension cords should have a grounding prong and the three
wires of the extension cord should be of the correct gauge.
• Keep visitors at a safe distance from work area.
• Keep children out of the workplace. Make workshop childproof.
Use padlocks, master switches or remove switch keys to pre-
vent any unauthorized use of power tools.
TOOL SHOULD BE MAINTAINED
• Always unplug tool prior to inspection.
• Consult manual for specific maintaining and adjusting proce-
dures.
• Keep tool lubricated and clean for safest operation.
• Remove adjusting tools. Form habit of checking to see that
adjusting tools are removed before switching machine on.
• Keep all parts in working order. Check to determine that the
guard or other parts will operate properly and perform their
intended function.
• Check for damaged parts. Check for alignment of moving parts,
binding, breakage, mounting and any other condition that may
affect a tool's operation.
• A guard or other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs. (Use
the parts list to order replacement parts.)
KNOW HOW TO USE TOOL
• Use right tool for job. Do not force tool or attachment to do a
job for which it was not designed.
• Disconnect tool from power when changing abrasive belt or
disc.
• Avoid accidental start-up. Make sure that the switch is in the
OFF position before plugging in.
• Do not force tool. It will work most efficiently at the rate for
which it was designed.
• Keep hands away from moving parts and sanding surfaces.
• Never leave tool running unattended. Turn the power off and
do not leave tool until it comes to a complete stop.
• Do not overreach. Keep proper footing and balance.
• Never stand on tool. Serious injury could occur if tool is tipped
or if belt or disc are unintentionally contacted.
• Know your tool. Learn the tool's operation, application and
specific limitations.
• Handle workpiece correctly. Protect hands from possible injury.
• Turn machine off if it jams. Belt jams when it digs to deeply into
workpiece. (Motor force keeps it stuck in the work).
• Support workpiece with miter gauge, belt platen or work table.
• Maintain
1
/
" maximum clearance between table and sanding
16
belt or disc.
CAUTION:
Think safety! Safety is a combination of operator
common sense and alertness at all times when tool is being used.
ASSEMBLY
Refer to Figures 3 and 4.
WARNING:
Do not attempt to operate tool until it is completely
assembled according to instructions.
CAUTION:
Do not attempt assembly if parts are missing. Use this
manual to order repair parts.
ASSEMBLE STAND
Refer to Figure 3.
NOTE: Finger tighten bolts and nuts until assembly is complete.
Then tighten all fasteners securely.
• Install foot by pressing onto all four legs.
• Attach one top frame to one pair of legs using carriage bolts,
flat washers and hex nuts. Repeat for second pair of legs.
• Attach one brace to each pair of legs using carriage bolts, flat
washers and hex nuts.)
• Connect the two leg sets with the two remaining top frames.
Make sure that the square holes in the legs align with the
square holes in the top frame. Also make sure that the slots on
top of the frame members are aligned at each corner. Secure
frames to legs using carriage bolts, flat washers and hex nuts.
• Attach the two remaining braces by aligning the square holes
in the legs and the braces. Insert carriage bolts, flat washers and
secure with hex nuts.
Top Frame
Carriage
Bolt
Flat
Washer
Figure 3 - Assemble Stand
MOUNT SANDER TO STAND
•
Place sander on the stand.
•
Align mounting holes of sander with slots on top frame.
•
Secure sander to stand on all four corners using four
hex head bolts, eight
5
ASSEMBLE DISC TABLE
Refer to Figure 4, page 4.
• Attach disc guard to end shield using three pan head screws,
three flat washers and three lock washers.
• Remove tape from key and armature. Slide aluminum disc with
abrasive disc onto armature with keyway in disc aligned with
key in armature. Secure disc to armature using set screw.
• Slide disc dust chute onto disc guard from below the 9" disc
with exhaust port to rear of tool. Secure dust chute to disc
guard with two pan head screws.
3
Hex
Nut
Brace
Leg
Foot
⁄
" flat washers and four
5
⁄
-18 hex nuts.
16
16
81093
5
⁄
-18 x 2"
16
Tabla de contenido
