Akron Brass Navigator Pro Instrucciones De Instalación, Funcionamiento Y Mantenimiento página 15

To manually assign the valve in a network installation, follow these steps:
1 . Navigate to the Valve Setup menu
2 . Press the ■ ENTER button to select "Valve Assignment"
3 . Press ■ OK to reassign the valve . Alternatively, the ■ CANCEL button can be pressed to exit the menu .
4 . If more than one valve is connected to the network, a list of serial numbers will be displayed . Use the
GREEN buttons to scroll through the list until the desired valve serial number is highlighted . Then press
and
the ■ SET button to assign the selected valve .
5 . The controller will re-start and is now assigned to the new valve .
Valve Name:
The Valve Name menu has options for identifying a valve by a name, as well as a number and a color . The name, number and color are all optional . If
set, they will be displayed in a bar across the top of the screen during normal operation . The number can be selected if there are multiple valves with the
same name; for example, Crosslay 1, Crosslay 2, etc . The name, number and color can also all be cleared so that nothing is displayed across the top of
the display (this is the factory default).
To configure the Valve name, number and color, follow these steps:
1 . Navigate to the Valve Setup menu
RED or
2 . Use the
3 . Press the ■ ENTER button to select "Valve Name"
RED or
4 . Use the
assigned valve . In no name is desired, select "None ."
5 . Press ■ SET to assign the name
6 . After the name is set, the Valve Number field will now be highlighted . Use the
select the desired number . If no number is desired, select "None ."
7 . Press ■ SET to assign the number
8 . After the number is set, the available Valve Colors will be shown . Use the
select the desired color . If no color is desired, select "White ."
9 . Press ■ SET to assign the color .
Valve Calibration:
When the valve is first installed, calibration must be completed to ensure accurate position sensor feedback to the system . This is only necessary at
installation or if a new motor driver, actuator or valve is installed .
****WARNING****
The valve will cycle open and closed during the calibration process . Be sure the system is not pressurized and the valve can be cycled open and closed
safely before proceeding with valve calibration .
To calibrate the valve, follow these steps:
1 . Navigate to the Valve Setup menu
RED or GREEN button to scroll through the list until the "Valve Calibration" is highlighted
2 . Use the
3 . Press the ■ ENTER button to select Valve Calibration
4 . Press the ■ START button to start the calibration process .
****WARNING****
The valve will cycle open and closed several times during the calibration process after the ■ START
button is pressed .
5 . When the calibration is complete, press the ■ OK button to complete the process .
Valve Options:
The valve options menu allows the user to change the following values:
• Turn the Auto Open on or off. The valve can be set to open from closed to fully open by pressing the open
button once instead of having to hold it down . If enabled, the valve will only auto-open if the valve is fully
closed . Once it is partially opened, it won't auto-open again until it is closed .
To adjust these settings, follow these steps:
1 . Navigate to the Valve Setup menu
RED or
2 . Use the
3 . Press the ■ ENTER button to select Valve Options
4 . Now the "Auto Open" field will be highlighted . Use the
ENABLED to activate auto open . Press the ■ SET button to save the value . If you do not wish to change this,
press the ■ DONE button to exit the valve options menu .
GREEN button to scroll through the list until the "Valve Name" is highlighted
GREEN button to scroll through the list and highlight the desired pre-loaded name for the
GREEN button to scroll through the list until the "Valve Options" is highlighted
RED or
RED or GREEN button to
RED or GREEN button to change the value to
Page 13
RED
GREEN button to