Tabla de contenido
Idiomas disponibles
Idiomas disponibles
first Aid Measures for Gel components (Ro400G only)
If gel within the comfort grip becomes exposed and results in skin contact wash with soap
and water;
For eye contact, flush with flowing water. If swallowed, seek medical attention.
material Safety Data Sheet (mSDS) available from 1-800-544-6986
SyMBolS
the label on your tool may include the following symbols.
V ........................... volts
Hz ......................... hertz
min ........................ minutes
...................... direct current
.......................... Class II Construction
.......................... safety alert symbol
Safety Warnings and Instructions: Sanders
• AlWAyS WeAR eye ANd ReSPIRAtoRy PRotectIoN.
• Clean your tool out periodically.
other Important Safety Warnings and Instructions
extension cords
when using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. the following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.
Minimum Gage for cord Sets
volts
120V
0-25
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V
0-50
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
more
Not more
than
than
0
-
6
18
6
-
10
18
10 -
12
16
12 -
16
14
Sanding
lead based Paint
Sanding of lead based paint is NOT RECOmmENDED due to the difficulty of controlling
the contaminated dust. the greatest danger of lead poisoning is to children and pregnant
women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis,
we recommend the following precautions when sanding any paint:
Personal Safety
• No children or pregnant women should enter the work area where the paint sanding is
being done until all clean up is completed.
• A dust mask or respirator should be worn by all persons entering the work area. The filter
should be replaced daily or whenever the wearer has difficulty breathing.
Note: Only those dust masks suitable for working with lead paint dust and fumes should
be used. Ordinary painting masks do not offer this protection. See your local hardware
dealer for the proper (NIOSH approved) mask.
• NO EATING, DRINkING or SmOkING should be done in the work area to prevent
ingesting contaminated paint particles. workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work
area where dust would settle on them.
environmental Safety
• Paint should be removed in such a manner as to minimize the amount of dust generated.
• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils
thickness.
• Sanding should be done in a manner to reduce tracking of paint dust outside the work
area.
cleaning and disposal
• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the
duration of the sanding project. Vacuum filter bags should be changed frequently.
• Plastic drop cloths should be gathered up and disposed of along with any dust chips or
other removal debris. they should be placed in sealed refuse receptacles and disposed of
through regular trash pick-up procedures. During clean up, children and pregnant women
should be kept away from the immediate work area.
• All toys, washable furniture and utensils used by children should be washed thoroughly
before being used again.
Motor
Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your
tool will operate on standard 60 hz household power. Do not operate AC tools on DC. A
rating of 120 volts AC/DC means that you tool will operate on standard 60 hz AC or DC
power. This information is printed on the nameplate. Lower voltage will cause loss of power
and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does
not operate, check the power supply.
operating Instructions
Always unplug sander from power supply before any of the following
WARNING:
operations.
WARNING: To reduce the risk of serious personal injury, read, understand and follow
all important safety warnings and instructions prior to using this tool.
Attaching Sandpaper
To attach sandpaper, carefully center the cloth side of the paper over the sanding pad. Press
the paper firmly in place. the hook and loop paper can be removed by simply pulling it off.
Switch - figure 1
To turn the tool ON, push the portion of the dust protected switch marked "I". To turn the tool
OFF, push the portion of the switch marked "O".
Holding the Sander - figures 2, 3, 4
the design of the Random Orbit Sander allows for several different gripping methods. three
basic methods are:
Figure 2 - One handed operation on the top of the sander.
Figure 3 - One handed operation holding the body of the sander.
Figure 4 - Two handed operation with one hand on the jug handle and the other on the body
or the top of the sander.
operation
Grasp the sander and turn it ON. move it in long, sweeping strokes along the surface, letting
it do the work. Utilize an even pressure across the sanding pad. excessive pressure in the
corner area may cause damage. Pushing down on the tool while sanding actually slows
the removal rate and produces an inferior quality finish. Check your work often. Sander is
capable of removing material rapidly.
dust extraction - figure 5, 6
WARNING: collected sanding dust from sanding surface coatings (polyurethane,
linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. to
reduce risk, empty bag frequently and strictly follow sander manual and coating
manufacturer's instructions.
Your sander comes equipped with a cloth dustbag to collect the dust generated while
sanding. to attach the dustbag onto the sander simply slide it firmly into the dust extraction
port at the back of the sander.
A ......................... amperes
w ........................ watts
.......................alternating current
n o ....................... no load speed
........................ earthing terminal
.../min ...............revolutions or
reciprocations
per minute
total length of cord in feet
26-50
51-100
101-150
51-100
101-200
201-300
American wire Gage
16
16
14
16
14
12
16
14
12
12
Not Recommended
To empty the dust dustbag, remove it from the sander by pulling it straight back. Dump the
sanding debris into an appropriate trash receptacle.
You may, if you prefer, attach a vacuum cleaner to the tool to collect the dust as you sand.
A vacuum hose adaptor is available as a service part at extra cost. to find your nearest
Black & Decker Service Center location, refer to the yellow pages directory under "Tools—
electric" or call: 1-800-544-6986.
To use the adaptor, remove the dust bag and replace it with the adaptor, then install a
vacuum hose.
ensure that the vacuum cleaner can be placed such that it will not tip over or interfere with
the motion of the sander. If this cannot be done, do not use the vacuum cleaner. Turn on the
vacuum cleaner before beginning to sand and turn it off after turning off the sander. empty
vacuum cleaner as required.
Maintenance / cleaning
Use only mild soap and damp cloth to clean the tool. many household cleaners contain
chemicals which could seriously damage the plastic and gel components. Also do not use
gasoline, turpentine, lacquer or paint thinners or similar products. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid.
IMPoRtANt: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
personnel, always using identical replacement parts.
tRouBleSHootING
Problem
Possible cause
• Unit will not start.
• Cord not plugged in.
• Circuit fuse is blown.
• Circuit breaker is tripped.
• Cord or switch is damaged.
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACk & DECkER help line at
1-800-544-6986.
Accessories
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986.
WARNING: the use of any accessory not recommended for use with this tool could be
hazardous.
Service Information
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
whether you need technical advice, repair, or genuine factory replacement parts, contact
the Black & Decker location nearest you. To find your local service location, refer to the
yellow pages directory under "Tools—Electric" or call: 1-800-544-6986.
full two-year Home use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. the defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should be
made within the time period of the retailer's policy for exchanges (usually 30 to 90 days after
the sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may
be required. Black & Decker owned and authorized Service Centers are listed under "Tools-
electric" in the yellow pages of the phone directory.
this warranty does not apply to accessories. this warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center. This
product is not intended for commercial use.
fRee WARNING lABel RePlAceMeNt: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
Black & Decker (U.S.)
Inc.,
701 E. Joppa Rd.
Towson, mD 21286
U.S.A.
Possible Solution
• Plug tool into a working
outlet.
• Replace circuit fuse.
(If the product repeatedly
causes the circuit fuse to
blow, discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Reset circuit breaker.
(If the product repeatedly
causes the circuit breaker
to trip, discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• have cord or switch
replaced at Black &
Decker Service Center or
Authorized Servicer.
See 'tools-
electric'
– yellow Pages –
for Service &
Sales
Tabla de contenido
