Tabla de contenido
Idiomas disponibles
Idiomas disponibles
SUMMARY :
- P reparing the concrete slab base
- Erecting the sides of the pool
- Screwing in the brackets
- Installing the tracks
- I nstalling the felt underlay and
the liner
- C utting out the liner, fitting the
backwash inlet nozzle and the skimmer
- Installing the coping
- Assembly of the pine edging
- The ladders
9
2* - IMPORTANT: It is important that the planks are correctly interlocked, especially those at the bottom
(where the pressure of the water will be greatest).
TO INTERLOCK A WARPED PLANK:
Even if they are on a pallet and wrapped in packaging, it is possible that some planks may be warped. This is entirely normal in view of the fact that
wood is a living material.
In order to install a warped plank, engage one of the two sides of the plank in position. Straighten the other side using 2 wooden wedges and the clamp.
Use the hammer and the sacrifice piece to engage it in position.
2a - Key point for assembling the structure. Use the cale to slot all the planks together. If the tongues which correctly align the planks when interlocked, are missing or have minor flaws,
this will not in any way affect the mechanical strength of the wood, its durability or the assembling of the pool.
2b - Make the first row of planks level.
2c - Push on the ends of the walls to press the structure onto the cradle.
2d - Control the shape using a tape measure (10m).
2e - Position the water jet plank on the 6th row. This can be either to the right or the left of the skimmer.
2f - P osition the lower plank for the skimmer on the 7th complete row. Complete the assembling of the structure by slotting together all the upper planks. Check the
alignment of the upper and lower skimmer planks.
3a - Positioning of the brackets, taking account of the top-bottom direction.
3b - Mark in the position of the brackets according to their height.
3c - Mark in the pre-drilling points on the side where the skimmer goes.
3d - Drill the holes for screwing on all the brackets.
3e - Put the brackets in place and screw them in so that the screw heads are fully embedded in the wood.
3f - Fix on the wooden stops for the skimmer flap.
3g - Cut to size the 45x135 post for the skimmer.
3h - Cut the 45x135 side support posts to the same length as the height of the pool.
3i - Mark in the drilling points, the same as for the brackets, and put up the posts. Drill all the planks on the sides of the pool.
3j - Screw in all the planks to the side support and fully embed the screw heads into the wood.
3k - Key point for assembling the brace covers.
3l - Mark in the fixture points for the brace covers and drill the sides of the pool.
3m - Screw in the supports, fully embedding the screw heads into the sides of the pool.
3n - Nail the 3 sections of the brace cover together.
4a - Screw the skimmer vent into the upper plank using 2 round headed screws which you will find in the bag of screws supplied in the skimmer box.
4b - Install the outer square seal for the skimmer and the skimmer itself.
4c - Fix the whole unit into place using 8 round headed screws which you will find in the bag of screws supplied in the skimmer box, tightening really well to ensure it is completely waterproof.
4d - After binding Teflon tape around the section of the valve that has been fed through (wrap tape around anti-clockwise at least 20 times), screw this into the skimmer.
Shut off the valve. Next, also bind Teflon tape around the grooved end that has been fed through. Screw this end into the valve. If the support post is hindering the task,
you could cut out a section of it to make the space needed.
4e - Drill the tracks according to the measurements (3cm from the ends and then approximately every 20cm).
4f - Unroll the felt underlay for the sides of the pool and place the plastic track flat onto the felt underlay, flush with the upper plank.
4g - Screw in the first track for the liner.
4h - Mark in where the corner cut is to be made.
4i - Cut out the corners as shown in the diagram. Screw in all the tracks.
4j - Feel where the skimmer frame is.
4k - Cut out the felt underlay around the outer edge of the skimmer.
4l - Do the same with the backwash inlet.
4m - Waterproof seal for skimmer frame/liner. Fit one of the 2 rectangular seals onto the skimmer frame ensuring that it is fully bonded.
4n - At the backwash inlet, fit the cork seal so that it is in contact with the side of the pool then fit one of the 2 round white seals on top of it, ensuring that they are fully bonded
5a - Put in place the protective felt underlay for the pool floor.
5b - Cut out the protective felt underlay using a Stanley knife or a pair of scissors.
5c - Put the liner in place when the outdoor temperature is between 20°C and 25°C.
5d - Hook the liner onto the lip of the track.
5e - Check that the liner is correctly positioned and smooth out the biggest creases.
5f - Adjust the corners of the liner to fit into the corners of the structure.
5g - Fill the pool with water to a depth of 2cm.
5h - Smooth out the creases in the liner. Resume filling until the water is 5cm below the backwash inlet nozzle.
6a - Stop filling when the water is just below the backwash inlet nozzle.
6b - Position the backwash inlet nozzle from the inside of the pool.
6c - Cut out the liner for the backwash inlet nozzle, leaving about 2mm play around it. Fit the seal and the backwash inlet nozzle.
6d - Tighten the outer nut on the backwash inlet nozzle enough to ensure it is waterproof, following the tip shown in the diagram if necessary.
6e - Bind Teflon tape around the ends that have been fed through, working in an anti-clockwise direction. Wrap round at least 20 times. Screw one of the ends to the
backwash inlet, the other one under the skimmer valve.
6f - Install one of the 4m pipes and secure in place using a metal collar.
6g - Put the other end of the pipe into the pool and resume filling until the water is 5cm below the skimmer.
6h– Mark in the position of the skimmer seal.
6i - Fix the skimmer seal and frame into place using 18 flat head screws which you will find in the bag of screws supplied in the skimmer box.
6j - Cut out the liner on the inside of the skimmer frame. Lastly position and clip in the flange cover.
6k – The water is at the correct level when it is halfway up the skimmer (having installed the filter).
7a – Place the finishing strips at each corner of the pool. Cut them to the height of the pool ensuring that you leave 2cm play between the end of the finishing strip and the coping.
7b – Fix the finishing trims in place using the nails supplied.
8
• (see page 32/33)
9
The ladders should not be used for any other purpose
The maximum weight limit is 150 kg
The means of access should be put in a safe place when not in use
9a - Put the ladder in position. To do that, expel the air from the steps if necessary.
9b - It can only be placed at certain points. See instructions for the cover.
9c - Secure the stainless steel supports using the bolts provided in the stainless steel ladder box.
NOTICE 300x490 - H120-2018/1 Sunwater new.indd 18
Before you start assembling the pool, check through the list provided on page 5 (warranty) to
make quite sure that you have all the necessary parts.
1a - Must be installed on a concrete slab. Thickness: 20cm minimum. Ensure that the slab is perfectly flat and level.
The minimum dimensions of the slab must be at least equal to those of the pool, including copings. Please see plan on page 20.
2 possible configurations:
1- If you are making the slab but do not yet have the metal brace (as you are awaiting delivery of
the pool), you can prepare the concrete slab, leaving a trench 18cm deep and 10 cm wide. Once
the pool has arrived, place the metal brace in the trench and fill it in with concrete, paying close
attention to the level (Drawing 1e).
2 - If you are making the slab and you already have the metal brace, you can embed this in the
concrete, paying close attention to the level (Drawing 1e). Make sure you plan for 1 to
3 depending on the type of pool.
Once the metal brace(s) has/have been removed from the packaging, it is absolutely essential that the wood
provided for the structure is repacked flat on the pallet and that it is all strapped together so as to avoid any
possible distortions.
1b - Place the structure in relation to the prevailing wind, the first wooden plank can provisionally be used to do this.
1c - Assemble the horizontal brace with the two vertical uprights.
1d - Positioning of the brace.
1e - Fill in the space with concrete.
There must be a concrete slab for the guarantee to be valid.
If using a safety tarpaulin, make sure to centre
the stainless steel ladder on the edging
17
09.01.18 08:41
Tabla de contenido
