Cleaning And Maintenance; Technical Data - camry CR 1150 Manual De Uso

13. PLAY / MODE
15. PLAY / PAUSE / MO / ST
17. Battery Cover
Before first use, unpack everything and remove all protective materials. Expand the power cord and antenna. Do not cover the
ventilation holes, make sure that around the radio there is a few centimeters breaks needed for proper ventilation.
SETTING THE CLOCK
1. Connect the device to the mains. The display (16) displays 00:00. Press CLOCK.SET (5). Displays shows 12 or 24. To set the clock
mode 12H or 24H use the buttons (12) and confirm with CLOCK (5). The unit will enter the edit hours mode. Select hour using the
buttons (12) and confirm with CLOCK (5).
2. Set the time using the buttons (12) and confirm with CLOCK (5). The device will go into edit minutes mode.
3. Set the minutes using the buttons (12) and confirm with CLOCK (5).
SETTING THE ALARM
1. In standby mode, press ALARM 1 or ALARM 2 (3 or 11). The display will show an icon.
2. Use the buttons (12) to set the desired alarm hour and confirm ALARM.
3. Use the buttons (12) to set the desired minute of alarm and confirm with button ALARM. The hour of the alarm is set.
4 .Press (12) to set the desired sound source: beep (bu), CD (CD) or radio (rd). If in the cover there is not CD, the device uses as the
source radio.
5. Confirm with ALARM. The clock icon indicates that the alarm is set. Once finished setting the alarm, you can turn it on or off by
pressing ALARM.
6. When the alarm is running, you can turn it off by pressing STANDBY (7) or the corresponding button ALARM.
7. When the alarm was started, the device can enter a state of "snooze" by pressing "SNOOZE" (8). Then the device will switch off for 9
minutes, then the alarm function is activated again.
AUTOMATIC SHUT-OFF TO
1. When the device is in the radio or CD mode, press and hold SLEEP / MEM (14) to select the time after which the device is switched
off (90, 80, 70 ... 10 minutes).
2. icon "zzz" on the display indicates that automatic shutdown is activated.
3. After the selected time the device turns off and switches to standby mode.
4. To disable this feature, press the STANDBY button (7).
LISTENING TO RADIO
1. Press STANDBY (7). Set the mode to radio using button FUNCTION (6).
2. Use the buttons (12) to tune in the desired radio frequency. After Press and hold for 2 seconds the button, radio will automatically find
the nearest frequency. Once it is found the search will stop.
3. The device searches for stations at 0.05 MHz frequency showing on the display with an accuracy of up to 0.1 MHz.
4. In order to remember the frequency of a radio station, press CLOCK SET / PROG. (5). Display shows P1. Use the SLEEP / MEM (14)
to select the program number where you want to save a sophisticated radio station.
5. Confirm the program number again press the button CLOCK (5). The program number will stop flashing.
6. Repeat the previous steps to program the stations (max 20 stations).
7. Use the SLEEP / MEM (14) to choose between preset programs.
8. Press (4) you can adjust the volume.
9. FM antenna is located on the rear panel. If the signal reception is weak, try moving the antenna and find a place where the signal is
strongest.
10. Button MO / ST (15) is to switch between mono and stereo reception. Changes can be made with good receptionof the station.
Playing Audio CD
Important: The CD player can play audio CDs. Some discs may not be readable due to mechanical damage, the quality of the media or
the software used to record the disc. There is no 100% guarantee of reading all the CDs. The device may not be compatible with all
files due to differences in coding.
1. Press STANDBY (7). Set the CD mode by pressing FUNCTION (6). CD icon is displayed. Mode starts reading discs.
2. Open cover with the button (9).
3. Insert the disc with the label facing up. Close the lid.
4. The display will indicate the number of tracks on the disc.
5. To start or pause disc playback, press the Play button (15). To resume playback, press the Play button again (15).
6. To go to the next or previous song, use the buttons (12).
NOTE: Pressing and holding the button scrolls the track forward or backward.
7. To stop playback completely, press the button (14).
PROGRAMMING order of songs
1. In CD mode after displaying the number of tracks, press CLOCK SET./PROG(5).
2. The display shows P1, where the digit represents the next programmed track.
3. Use the buttons (12) to select the track to be saved under a particular number.
4. Press the PROG (5) to confirm your selection. Repeat steps 2-3 to program up to 20 tracks.
5. Press (15) to start playback. Playback will end after all the tracks. To play it again, press the button (15).
6. To cancel a programmed sequence, press the STOP button (14) or open the lid of the player.

CLEANING AND MAINTENANCE

1. The unit can be wiped with a dry cloth only.
2. Periodically clean the CD with a special cleaning disc.

TECHNICAL DATA

Power supply: 230V ~ 50Hz
Backup Clock: 2 x LR03 (AAA)
RMS Output Power: 2x 0,8 W
Power: 15W
14. SLEEP / STOP / MEM
16. Display