Manuales relacionados para GE PVB37
Resumen de contenidos para GE PVB37
- Página 1 Installation Instructions Downdraft Vent Systems PVB37 PVB67 PVB94 PVB98 ZVB30 ZVB36 31-10728 09-09 JR...
-
Página 2: Before You Begin
Safety Information befoRe you beGIN WARNING: To ReDuce The RISk Read these instructions completely and carefully. of fIRe, elecTRIc Shock oR INjuRy To peRSoNS, IMpoRTANT obSeRVe The folloWING. • – Save these instructions A. Use this unit only in the manner intended by for local inspector’s use. -
Página 3: Tabla De Contenido
Design Information coNTeNTS Design Information Ductwork Product Dimensions ..............3 Duct Fittings ................10 Accessories.................. 3 Installation Instructions Advance Planning ............... 4, 5 Step 1, Install Downdraft Vent ......... 11 Installation preparation Step 2, Install the Ductwork ..........11 Clearances ................6, 7 Step 3, Install Control Switch .......... -
Página 4: Advance Planning
The installation of these downdraft vents with 3. Review the cabinet illustration. Check to be sure any GE or Monogram cooktop requires careful the interior cabinet depth will house the cooktop consideration. Before you begin, review the burner box, the vent and the cutout clearance combination cutout illustrations on page 6. -
Página 5: Clearances
• Install a standard electrical outlet within reach of the vent’s two-foot-long power cord. • If clearance is less than 30", protect cabinet • The vent and a GE or Monogram gas cooktop bottoms with flame-retardant millboard at least combination can operate from the same 120-volt 1/4"... -
Página 6: Installation Preparation
Installation preparation cuTouTS AND cleARANceS • Measure carefully when cutting the countertop. • Refer to cooktop installation instructions to Make sure sides of the opening are parallel and be sure that models fit into the base cabinets rear and front cuts are exactly perpendicular being used. -
Página 7: Parts Supplied
Installation preparation cleARANceS cAuTIoN: Wall coverings, countertops and cabinets should withstand 200° heat generated by any cooktop. Gas - 6" to 12" Electric - 2" Clearance to Side Walls 13" 13" Max. Max. 682Dia40 a 30" 30" Min. 18" Min. 18" Min. -
Página 8: Power Supply
15- or 20-ampere circuit breaker or time-delay fuse. IMpoRTANT Gas cooktops If this vent is installed in combination with a GE (please read carefully.) 682Dia47 or Monogram gas cooktop, it may operate from The power cord of this appliance is equipped the same duplex outlet. -
Página 9: Venting Options
Installation preparation VeNTING opTIoNS Loosen Screws to Adjust 3-1/2" to • The downdraft vent is shipped with the Left or Right discharge outlet pointing straight down and can be changed to the left or right side. • The blower outlet is sized for 3-1/4" x 10" and can be transitioned to 6"... -
Página 10: Duct Fittings
Total Duct Run systems, follow the *Actual length of straight duct plus duct fitting equivalent. Equivalent length of duct pieces is based heating equipment on actual tests conducted by GE Evaluation Engineering Dia14.C manufacturer’s Dia14.D Dia14.E and reflect requirements for good venting performance guidelines and safety with any downdraft cooktop. -
Página 11: Installation Instructions
Installation Instructions 1 INSTAll DoWNDRAfT VeNT 2 INSTAll DucTWoRk Place the downdraft vent into the countertop • The downdraft blower system is designed for use cutout, against the back side. with 3-1/4" x 10" ductwork. It can be transitioned to 6" round. bracket location for right-side or straight- •... -
Página 12: Step 3, Install Control Switch
Installation Instructions 3 INSTAll coNTRol SWITch (on some models) Skip this step if there is no separate control switch. WARNING: Disconnect electrical power from unit before beginning switch installation. Failure to do so could result in personal injury or damage to the electrical controls. -
Página 13: Step 4, Connect Power
Installation Instructions 4 coNNecT poWeR cleANING painted or Stainless Steel Surfaces Plug power cord into properly grounded receptacle. To clean the stainless steel or painted surfaces, use warm, sudsy water or a stainless steel cleaner or polish. 5 INSTAll fIlTeRS, check opeRATIoN The filters should be washed by hand. - Página 14 Notes...
- Página 15 Notes...
- Página 16 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. 31-10728 09-09 JR...