Idiomas disponibles
Idiomas disponibles
C. HOW TO LOAD YOUR GREASE GUN WITH A LUBRICANT CARTRIDGE:
1. Unscrew the Head Assembly from the barrel of the Grease Gun (See Figure 1). Pack head with Grease (See Figure 2).
2. Pull back the Plunger Rod. When the rod is fully extended, the Plunger Rod locks into place with posi-stop Plunger Lock.
3. Remove the plastic cap from the end of Grease Cartridge and, insert open end first, into the barrel of Grease Gun (See Figure 6)
4. Push the Grease Cartridge into the barrel until the rim of the pull-tab end contacts the rim of the barrel (See Figure 7).
Then remove the pull-tub seal from the end of the Grease Cartridge (See Figure 8).
5. Screw the head back onto the barrel. Tighten the Head Assembly securely (See Figure 4).
6. Unlock the Plunger Rod from the end cap, by releasing the Plunger Lock. This would push the Plunger Rod into the barrel.
7. See Point A (7).
Problem: Gun will not dispense Grease
Possible Cause:
1. Grease Cartridge or Barrel is empty.
2. Air is trapped in the Grease Gun head.
Solution:
• Replace the grease cartridge or refill the barrel.
• Expel the trapped air, while pressing the Air Bleeder Valve, and pushing the Plunger (Follower) Rod handle.
Problem: Grease Cartridge will not empty completely. Also, if you are not sure whether the Cartridge is completely empty or not.
Possible Cause: Tabs on rod are binding to rubber plunger assembly.
Solution:
• Connect the rod to the rubber plunger assembly.
• Push the rod into the barrel as far as it will go to move the grease forward.
• Measure the rod handle from the end cap on the barrel to the tip of the rod handle.
• If the measurement is more than 1-3/4", the grease cartridge is not empty.
• If not completely empty, disconnect rod from rubber plunger assembly after grease has been pushed forward.
Problem: Grease leakage visible between Barrel and Head Assembly
Possible Cause: Initial tightening of Barrel into Head Assembly not sufficient or the Rubber Seal inside the Head Assembly is damaged or missing.
Solution:
• Tighten Barrel into Head Assembly securely or replace the Rubber Seal
Problem: Grease leakage visible at Extension or at Head Assembly
Possible:
1. Initial tightening of extension into Head Assembly and/or Coupler not sufficient
Cause:
4. Worn or damaged piston and/or bore in Head Assembly
Solution:
• Tighten Extension into Head Assembly and Coupler into the Extension
• Tighten Filler Nipple into Head Assembly securely
• Replace "O" Ring or Air Bleeder Valve
Lumax warrants all lubrication equipment manufactured by Lumax to be free from defects in material and workmanship on the date of sale by an authorized Lumax distributor to the original purchaser for use. Lumax
will during one (1) year, following the date of purchase, repair, or replace any part of the equipment determined by Lumax to be defective. This warranty applies only when the equipment is installed, operated, and
maintained in accordance with Lumax written recommendations. Lumax does not make any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product or that
he or she is qualified to replace any parts of the product. In fact, Lumax expressly states that all repairs and parts replacements should be undertaken by certified and licensed technicians and not by the buyer. The
buyer assumes all risk and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of replacement parts thereto. If equipment proves to be
defective during this warranty period, it will be repaired or replaced without charge, provided that factory examination indicates the equipment to be defective.
This warranty does not cover, and Lumax shall not be liable for general wear and tear, accident, overload, or any malfunction, damage, or wear caused by faulty installation, misapplication, misuse, abuse, abrasion,
corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Lumax component parts. Nor shall Lumax be liable for the equipment repaired or altered by anyone not
authorized by Lumax to repair or alter the equipment. Lumax will also not be liable for malfunction, damage, or wear caused by the incompatibility of Lumax equipment with accessories, equipment or materials not
supplied by Lumax. This warranty is extended to the original retail purchaser only and is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Lumax distributor for verification
of the claimed defect. If the claimed defect is verified, Lumax will repair or replace free of charge any defective parts. The equipment will be returned to the original buyer, transportation prepaid. If inspection of the
equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the cost of parts, labor, and transportation. This warranty is exclusive,
and is in lieu of any other warranties, express or implied, including but not limited to warranty of merchantability or warranty of fitness for a particular purpose. Lumax sole obligation and buyer's sole remedy for
any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including but not limited to, incidental or consequential damage for lost profits, lost sales, injury to person or property, or
any other incidental or consequential loss) shall be available. In no event shall Lumax be liable for incidental or consequential damages. The liability of Lumax on any claim for loss or damage arising out of the sale,
resale, or use of lubrication equipment, materials dispensing equipment, and other related equipment should in no event exceed the purchase price. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. Any action for
breach of warranty must be brought within two (2) years from the date of sale.
Lumax makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials, or components sold but not manufactured
by Lumax (such as Electric Motors, Switches, Hoses, etc.) are subject reasonable assistance in making any claim for breach of these warranties. In no event will Lumax be liable for indirect, incidental, special, or
consequential damages resulting from Lumax supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of
warranty, the negligence of Lumax or otherwise. Any implied warranties applicable to lubrication equipment, materials dispensing equipment, and other related equipment manufactured by Lumax, including the
warranties of merchantability and fitness for a particular purpose, will last only for one (1) year from the date of purchase. Some states do not allow limitations on how long an implied warranty last, so the above
limitation may not apply to you.
© 2015 Lumax. All Rights Reserved. Lumax and the Products described in it are Copyrighted by Lumax, with All Rights Reserved.
This Form may not be Copied in Whole or Part, without the Express Written Consent of Lumax.
Lumax, USA
www.Lumax.com
LIMITED WARRANTY POLICY ON NEW EQUIPMENT. PLEASE READ THE FOLLOWING CAREFULLY
Troubleshooting Chart
2. Filler Nipple may be loose
3. Worn Air Bleeder Valve "O" Ring
Figure 6
Figura 6
Figure 6
Figure 7
Figura 7
Figure 7
Figure 8
Figura 8
Figure 8
Form:
LX-1160-61-IS
