Tabla de contenido
Idiomas disponibles
Idiomas disponibles
PROGRAMMING OF THE INTERMEDIATE
POSITION OF THE END-OF-STROKE
To set the intermediate position of the end-of-stroke it is
necessary to use a remote control previously stored and
proceed as follows:
1.
Bring the roll-up shutter to the INTERMEDIATE position
desired
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 6 flashes
4.
Press the UP+DOWN keys of the transmitter until the motor
confirms the storage of the intermediate position moving in
both directions for 1/2 seconds
5.
Release the keys
6.
To exit the programming mode press the STOP key
To bring the roll-up shutter to the intermediate position
press the STOP key for at least 3 seconds (when the motor
is stopped): the roll-up shutter moves until it reaches the
stored position.
To delete the intermediate position previously stored it is necessary
to use a remote control previously stored and proceed as follows:
PROGRAMMING THE WIND SENSOR
INTERVENTION THRESHOLD
m
CAUTION: to trigger the closing of the sunshade, the wind
sensor must detect a value greater than the set threshold for at
least 5 seconds. The closure of the sunshade caused by strong
wind stops the automated system for 8 minutes.
To set the wind sensor intervention threshold, it is
necessary to use a remote control previously stored and
proceed as follows:
1.
Supply power only to the control unit to be programmed
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 7 flashes
4.
Press the UP+DOWN keys until the motor moves in jerks
which confirms it is entering the programming phase.
The number of jerks made by the motor corresponds to the
level currently set:
1 jerk = level 1 = 10 Km/h
2 jerks = level 2 = 15 Km/h
3 jerks = level 3 = 20 Km/h
4 jerks = level 4 = 30 km/h (default value)
5 jerks = level 5 = 40 Km/h
5.
Release the keys
6.
To increase the level press the UP key and to decrease it
press the DOWN key, as soon as the control unit receives the
command, it shows the new level by operating the motor
with a corresponding number of jerks
7.
When the desired value is reached, press the STOP button:
the control unit will show the set value again to confirm
8.
To exit the programming mode press the STOP key
PROGRAMMING THE SUN SENSOR
INTERVENTION THRESHOLD
m
CAUTION: to trigger the opening of the sunshade, the sun
sensor must detect a value greater than the set threshold for at
least 8 minutes. To trigger the closing, the sensor must detect a
value below the set threshold for at least 8 minutes. Interruptions
of light (due to clouds) shorter than 1 minute are not detected,
while if they exceed 1 minute, the 8-minute timer is reset.
To set the sun sensor intervention threshold, it is necessary
to use a remote control previously stored and proceed as
follows:
1.
Supply power only to the control unit to be programmed
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 8 flashes
4.
Press the UP+DOWN keys until the motor moves in jerks
which confirms it is entering the programming phase.
The number of jerks made by the motor corresponds to the
level currently set:
1 jerk = level 1 = 2 klux
2 jerks = level 2 = 5 klux
3 jerks = level 3 = 10 klux (default value)
4 jerks = level 4 = 20 klux
5 jerks = level 5 = 40 klux
5.
Release the keys
6.
To increase the level press the UP key and to decrease it
press the DOWN key, as soon as the control unit receives the
command, it shows the new level by operating the motor
with a corresponding number of jerks
7.
When the desired value is reached, press the STOP button:
the control unit will show the set value again to confirm
8.
To exit the programming mode press the STOP key
PROGRAMMING THE TEMPERATURE LEVEL
This function allows you to adjust the temperature to 5 levels,
below which the sun sensor must not open the sunshade, even if
the light intensity exceeds the level set.
This feature is particularly useful in countries with a cold climate,
where sunny dyas are frequent but very cold. In these situations,
it is not necessary to open the sunshade that would prevent the
sunlight from heating the indoor environment.
To set the temperature level, it is necessary to use a remote
control previously stored and proceed as follows:
1.
Supply power only to the control unit to be programmed
2.
Activate the LOKI programming
3.
Press the UP or DOWN keys until the led performs n. 9 flashes
4.
Press the UP+DOWN keys until the motor moves in jerks
which confirms it is entering the programming phase.
The number of jerks made by the motor corresponds to the
level currently set:
1 click = level 1
2 clicks = level 2
3 clicks = level 3
4 clicks = level 4
5 clicks = level 5
5.
Release the keys
6.
To increase the level press the UP key and to decrease it
press the DOWN key, as soon as the control unit receives the
command, it shows the new level by operating the motor
with a corresponding number of jerks
7.
When the desired value is reached, press the STOP button:
the control unit will show the set value again to confirm
8.
To exit the programming mode press the STOP key
- 10 -
= sensor disabled (default value)
= 0°C
= 5°C
= 10°C
= 15°C
Tabla de contenido
