Tabla de contenido
Idiomas disponibles
Idiomas disponibles
SECTION B - SYSTEMS WITH SMART-LEARN BUTTON
Locate your SMART-LEARN BUTTON on your system. It will be located on the side or
back panel of the motor unit.
Note: If your SMART-LEARN BUTTON is RED your system is NOT COMPATIBLE
with the Clicker 321. You have a system with rotating codes.
Choose a random 9-digit code. Your code may only consist of numbers
1,2 or 3. Example: 122313213. Fill in the TABLE below entering any combination
of 1,2 and 3.
CODE SWITCH SEQUENCE
1 2 3 4 5 6 7 8 9
Step 1: Press the 1st and 3rd buttons down simultaneously and hold until the red
indicator starts to blink. Release both buttons. Wait for the red indicator to stop
blinking.
Step 2: Press the button you want to use to operate your garage door opener 4 times.
Wait for the red indicator to blink the same number of times.
Step 3: Using the random 9-digit code from table above, press and release the button that
corresponds with the number in each column until the entire code has been entered into
the Clicker. Immediately after the code is entered, the indicator light will
blink 4 times.
Step 4: Press and release smart-learn button on motor unit. (Indicator light next to the smart-learn button
should turn on.) Press and hold the Clicker button you selected until the motor unit lights blink. If light bulbs
are not installed, two clicks will be heard.
Programming is complete. To test press the button you selected to activate the garage door. If programming is
unsuccessful, repeat Steps 1 – 4 above.
Note: To program additional doors, proceed to the appropriate section using another button in step 2.
5 Genie (9 Code Switches) • 6 Genie (12 Code Switches)
Locate your systems code switch positions from an original hand held remote or the motor unit receiver.
If the switch is "on" or "up", place a 1 in the corresponding box in the TABLE below. If the switch is "off"
or "down", place a 3 in the corresponding box in the TABLE below.
CODE SWITCH SEQUENCE
ON/UP
OFF/DOWN
PROGRAMMING
Before you begin programming the Clicker, select which button you want to
operate your garage door opener. After completing a step, you have 15 seconds
to proceed to the next step.
Step 1: Press the 1st and 3rd buttons down simultaneously and hold until the red indicator
starts to blink. Release both buttons. Wait for the red indicator to stop blinking.
Step 2: Press the button you want to operate your garage door opener: Genie (9 code
switches) press the button 5 times; Genie (12 code switches) press the button 6 times. Wait
for the red indicator to blink the same number of times.
Step 3: Using the code switch sequence from the table above, press and release the button that corresponds
with the number in each column until the entire code has been entered into the Clicker. Immediately after the
code is entered, the indicator light will blink (five times for Genie 9 code switches; six times for Genie 12 code
switches).
Programming is complete. To test press the button you selected to activate the garage door.
If programming is unsuccessful, reverse code from TABLE above. (Change 1 to 3; 3 to 1).
Repeat Steps 1-3 above.
Note: To program additional doors, proceed to appropriate section using another button in step 2.
BATTERY REPLACEMENT
The lithium batteries supplied with your Clicker should last 3 to 5 years under normal use of 6 operations per
day. If you experience continued short range, intermittent operation, or a reduced glow of the red indicator
light, replace the batteries. To Replace batteries: Pry open the Clicker using a flat head screwdriver. Remove
the screw from the center of the circuit board and carefully lift out board. Remove plastic battery shield and
batteries. Insert new batteries, replace battery shield and circuit board and close the Clicker case.
Note: Be sure to position the metal strip underneath the batteries.
TECHNICAL SUPPORT: 800-442-1255 (MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door
Corporation. Linear and Multi-Code are Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is
a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. DoIt is a trademark of DoIt Best Corporation.
114A2356C
PROGRAMMING
Before you begin programming the Clicker, select which button you
want to operate your garage door opener. After
completing a step, you have 15 seconds to proceed
to the next step.
1 2 3 4 5 6 7 8 9 10 11 12
©2001, Clicker Corporation
All Rights Reserved
1
2
3
9
9
1
7
3
7
5
5
KG
KG
Indicator Light
"Smart" (learn)
Button
Step 1
Step 2
Step 3
Step 1
Step 2
Step 3
Printed in Mexico
1
3
Tabla de contenido
