Sammic Danamix DX Serie Instrucciones página 4

MODELS
This manual describes the installation,
operation and maintenance of the DX-250,
DX-350, DX-550, DX-750, DXC-250
DXC-350 portable electric appliances.
The model reference and its specifications
are shown on the nameplate affixed to the
machine.
These appliances have been designed and
manufactured in accordance with the
following standards:
European Directives and Standards
(Version fed at 230V, 50/60Hz)
- Low Voltage Directive: 73/23/EEC
- Machine Directive: 89/392/EEC
- Electromagnetic Compatibility Directive:
89/336/EEC
- Amendment to directives: 93/68/EEC
- Standards for machine safety: UNE-EN
60335-2-64 and 60335-1
- Interference Emission Norms: UNE-EN
55014, 61000-3-2 and 61000-3-3
- Interference Immunity Norms UNE-EN
55014-2
- Degree of protection IP 24 according to
norm IEC 60529 Standard.
Applicable American Standards (Version
fed at 115V, 60Hz)
- Standards for Machine Safety: UL 1097,
UL 763, UL 94
- Standards for Hygiene and Food Equipment
Materials: ANSI-NSF 8 and ANSI-NSF 51
INSTALLATION AND OPERATION
For optimum performance and long service
life of the machine, follow the installation
and start-up instructions contained in this
manual rigorously as well
recommended conditions of use.
Installation
Before plugging the appliance, check for a
match between the mains voltage and the
appliance voltage as specified on the
nameplate.
There is a wall mount supplied with the
appliance. Determine an appropriate location
for this support.
Directions for Use
Plug the appliance into an outlet.
4
ENGLISH
Introduce the foot into the bowl, up to a
maximum of 2/3 the foot's length. For
optimum operation, it is better if the foot
does not touch the bottom of the bowl. In
and order to prevent splashed food from
getting inside the motor unit, it is
recommended not to incline the appliance
more than 30º (See Figure 6).
Once finished
appliance if it is not going to be used
again.
In the event of overheating due to
prolonged use or overload, the thermal
switch would protect the motor, stopping
it. If this occurs, allow the blender to cool
before restarting it.
Function of the controls
M DX-250 (See Figure 3)
ODEL
ON/OFF switch (6): Pressing this button
together with the Safety one (7) will cause
the appliance to operate.
Safety (7): If this button is not actuated, the
appliance will not start. Once in operation,
the appliance will not stop when this push-
button is released.
Variator control (12, model DXC-250 only):
serves to change the speed of the blade or
stirrer.
M DX-350, 550
ODELS
4 and 5)
ON/OFF switch (9): Pressing this button
together with the Safety one (11) will cause
the appliance to operate. Unless locked,
the appliance will stop as soon as this
push-button is released.
Safety (11): If this button is not actuated,
the appliance will not start. Once in
operation, the appliance will not stop when
this push-button is released.
as the Lock (10): This button is intended to lock
the appliance in the operating condition, so
that it operates even when all push-buttons
are released. Unlocking the appliance is
achieved by pressing the 'Start' button
again (9).
Variator control (8, model DXC-350 only):
serves to change the speed of the blade or
stirrer.
F
ITTING OF THE BLENDER
DX-350, DX-550 and DX-750)
Insert the coupling shaft of the blender (2)
into the motor unit (1) and turn the foot
counterclockwise
clamped.
F
DXC-350)
Insert the coupling shaft of the beater (3)
into the motor unit (1) and turn the foot
counterclockwise
clamped.
F
working, unplug the DXC-250 and DXC-350)
Fitting: introduce the end of the stirrer into
the hole in the gear attachment, turning
and pushing the same to a stop.
Removing: Pull firmly from the stirrer until
it comes off the gear attachment.
MAINTENANCE
- If the power cord gets damaged and must
- The blades wear in time and have to be
- Check regularly the foot and gear
Cleaning and hygiene
W
- To avoid electric shocks that can cause
750 (See Figures
AND
- In order to avoid damage to people and
- Do not use the following products:
These products would score, scratch and
damage the metallic and plastic surfaces of
the appliance.
Cleaning Procedure
After each use, place up to 2/3 of the
length of the liquidiser arm in a recipient
containing hot water (35-45ºC · 95-113ºF)
(models DXC-250, and switch on for a few seconds.
The tube (5) and the blade must be washed
with hot water (35-45ºC · 95-113ºF) and an
Ivory Liquid type of multi-purpose liquid
until it is securely detergent in a proportion of 1 measure of
detergent per 10 measures of water, leaving
(models DXC-250 and
ITTING OF THE BEATER
until it
/
ITTING REMOVING OF THE STIRRER
be replaced, such a change may only be
done by a approved technical assistance
service.
replaced periodically.
attachment for tightness.
ARNINGS
severe injury or death, always unplug the
blender before cleaning. Once cleaned,
connect it again.
the appliance, read and follow the
manufacturer's instructions
cleaning of the blender.
- Abrasive cleaners, such as ammonia,
lye, etc.
- Solvents
- Metal scourers
- Gritty detergents.
is securely
(models
for the