Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
FOLLOW INSTALLATION INSTRUCTION IN INSTALLATION MANUAL IN19-04
FOLLOW PRECAUTIONS IN OPERATOR'S MANUAL IN17-04
A. IMPORTANT: Disconnect battery prior to installing electric/hydraulic activation kits.
B. Locate the wiring harness provided with your PTO. Separate the harness at the 4-wire connector.
C. The engine compartment section has the connection to the PTO activation solenoid and pressure
switch. Make the connection to both components.
D. Feed the 4-wire connector (white) through to the inside of the cab. Use a pass-through or drill a ⅝"
hole and use the grommet provided in your kit. Connection to the Ford wiring is located in the cab.
Locate the blunt cut body builder wires provided by Ford as described in this supplement.
E. Follow the diagrams for your vehicle engine type and operation mode.
Install the Muncie Power switch and indicator light into the Muncie Power switch bracket.
Note: Ford Auxiliary switches cannot be used for the "Stationary AND Mobile" installations.
Ford SEIC Connector Location – (Passenger Side)
Locate the FORD wire bundled together at the PASSENGER SIDE behind the kick panel at the
passenger's feet.
The Muncie Power harness passes through into the cab. Locate the Muncie Power connector and
make the connection to the Ford connector. Wire colors and pin locations are as show in the charts on
the next page for the harness provided.
F20 10-BOLT PTO ACTIVATION
Ford 10R140 Series Transmissions
2020 and later F-250 — F-600
Resumen de contenidos para Muncie F20
- Página 1 Locate the FORD wire bundled together at the PASSENGER SIDE behind the kick panel at the passenger’s feet. The Muncie Power harness passes through into the cab. Locate the Muncie Power connector and make the connection to the Ford connector. Wire colors and pin locations are as show in the charts on...
- Página 2 Single Mode (Either Stationary OR Mobile) Installation For Dual Mode (Stationary AND Mobile), see reverse side of this document. 2020 & Later F-250 – F-600 DIESEL Engine – Single Mode Wire Harness 34T43730 (F20-F1312-DX5**P*) MUNCIE HARNESS COLOR FORD WIRE COLOR...
- Página 3 649 OHM resistor is now parallel with the potentiometer inside the RPM control module. Install the Muncie Power switch and indicator light into the Muncie Power switch bracket. Note: Ford Auxiliary switches cannot be used for the “Stationary AND Mobile” installations.
- Página 4 201 East Jackson Street • Muncie, Indiana 47305 800-367-7867 • Fax 765-284-6991 • [email protected] • www.munciepower.com Specifications are subject to change without notice. Visit www.munciepower.com for warranties and literature. All rights reserved. © Muncie Power Products, Inc. (2020) A Member of the Interpump Group IN19-05 (Rev. 01-20)
-
Página 5: Ubicación Del Conector Seic De Ford - (Lado Del Pasajero)
E. Siga los diagramas para el tipo de motor y modo de operación de su vehículo. Instale el interruptor de Muncie Power y la luz indicadora en el soporte del interruptor de Muncie Power. Nota: Los interruptores auxiliares Ford no se pueden usar para instalaciones “estacionarias Y móviles”. - Página 6 RPM. Instale el interruptor de Muncie Power y la luz indicadora en el soporte del interruptor de Muncie Power. Nota: Los interruptores auxiliares Ford no se pueden usar para instalaciones “estacionarias Y móviles”.
-
Página 7: Instalación En Modo Simple (Ya Sea Estacionaria O Móvil)
Para conocer el procedimiento para el modo doble (estacionario Y móvil), vea el reverso de este documento. 2020 y Motor DIESEL F-250 – F-600 – Modo simple posteriores Arnés de cableado 34T43730 (F20-F1312-DX5**P*) NRO. DE COLOR DEL ARNÉS DE MUNCIE... - Página 8 800-367-7867 • Fax 765-284-6991 • [email protected] • www.munciepower.com Las especificaciones están sujetas a cambios sin previo aviso. Visite www.munciepower.com para conocer las garantías y el material informativo. Miembro de Interpump Group Todos los derechos reservados. © Muncie Power Products, Inc. (2020) IN19-05 (Rev. 01-20)