Tabla de contenido
Idiomas disponibles
Idiomas disponibles
IV. Initial setup
1.
Start by installing the two AAA batteries supplied inside the remote control.
2.
Plug the AC cable into a wall outlet.
3.
Next, insert the 3.5mm plug cable of the second satellite speaker into the 3.5mm jack labeled 'light' located on
the back panel of the main unit.
4.
Connect the RCA plug cable of the second satellite speaker into the RCA jack labeled 'output' located on the
back panel of the main unit.
5.
Connect the 3.5mm plug cable into the corresponding auxiliary and/or DVD port of the main speaker's back panel.
6.
Proceed to connect the other side of the 3.5mm jack into the media device of choice, such as a laptop,
television set, MP3/4 player, smartphone or tablet.
7.
Connect the antenna to the RCA jack labeled 'Antenna' on the main speaker's back panel.
8.
Turn on the speaker by pressing the red power button on the remote control.
9.
Select the input mode of choice using the SOURCE button on the main unit or by pressing the corresponding
button on the remote control.
10.
Use the controls on the front of the main unit or the remote control to start enjoying the speaker system.
11.
Press and hold the Power button on the remote control to put the unit in Stand By mode.
V. Advanced operation
Pairing the speaker with your Bluetooth
device
®
Note: Before installing this product, please make sure your device is compatible with Bluetooth
speaker will connect to only one device at a time. In order to connect to the unit verify that there is
no other device already paired with it.
1.
Press the Power button
on the remote control to turn ON the unit.
2.
Enable the Bluetooth
function on the device of choice and set it to discover the wireless speaker.
®
3.
Next, press the SOURCE button on the speaker or on the remote control to enable the Bluetooth
The bl icon appears on the screen to indicate that the system has entered into the pairing mode.
4.
Once the speaker appears listed under the newly found Bluetooth
seconds for pairing.
5.
If pairing is successful, it will indicate that the speaker system is connected. If after 60 seconds the pairing
process fails, please repeat steps 2 through 5 described above.
6.
You can now start streaming audio through the speaker wirelessly from your favorite Bluetooth
devices.
7.
The speaker will re-pair automatically to the memorized device when the BT mode is selected on the unit
after being turn off and on again.
. The
®
feature.
®
devices (KFS-600), select it and wait a few
®
- enabled
®
Technical specifications
MPN
Device
Type
Maximum power output (PMPO)
Reference RMS power
DC input
Buttons
AC input
Driver
Driver unit
Reference RMS power
Frequency
Impedance
Sensitivity
Signal to noise ratio
Total harmonic distortion (THD)
Microphone
Directivity
Frequency
Impedance
Sensitivity
Connectivity
Connection type
Memory card slot
Auxiliary port
Others
Additional information
LED illumination
Dimensions (WxHxD)
Weight
Cable length
Warranty
KFS-600
Floor standing speaker system (set of two)
2800W
300W
20V
ST-BY/PLAY PAUSE, SOURCE, VOL+/-
NEXT TRACK, VOL-PREVIOUS TRACK/,
TONE
110V-240V (autosensing)
Four 5.25in subwoofers
Four 2.5in tweeters
300W
Tweeter: 60Hz-20kHz
Subwoofer: 20Hz-170Hz
Subwoofer: 8
Tweeter: 8
870mV
≥60dB
≤ 1%
Unidirectional
75Hz-14kHz
530 ±30% (at 1kHz)
-71dB±3dB
compatible, two 3.5mm auxiliary
Bluetooth
®
ports and FM
USB
Two 3.5mm jacks
Two ¼in ports
Adjustable multicolor patterns: LED1,
LED2, LED3, LED4, LED5, LED6, LEDF (OFF)
6.7x33x13.1in
40lb
4.9ft
One year
Tabla de contenido
